Request a Quote

Power distribution equipment

Variable-Frequency Drive Panels

We build new variable-frequency drive panels in the U.S. with American components and ship nationwide. Review enclosure, harmonics, cooling, and cable interfaces against each motor and installation.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Rows of gray electrical distribution cabinets on pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start with the Drive and Motor Duty

A drive panel begins with the motor and the work it must perform, not simply a horsepower value. Provide motor nameplate data, voltage, full-load current, insulation details, speed range, starting frequency, and the driven load. Pump, fan, conveyor, and high-inertia duties can impose different acceleration and braking needs.

Also describe operating patterns: expected starts per hour, continuous or intermittent service, overload requirements, and any need for coordinated operation with other drives. These details help establish a suitable drive rating and panel arrangement. Final selections should be checked by the responsible engineer against the application and system design.

Choose an Enclosure for Its Environment

Enclosure construction should reflect the installation location, access needs, and exposure to dust, moisture, corrosive agents, or washdown. Indoor electrical rooms and outdoor process areas present different constraints. Confirm the required enclosure rating, mounting method, available footprint, working clearances, and door access before fabrication is defined.

The panel can be configured around the drive, disconnecting means, protection, control devices, and specified accessories, subject to the project requirements. Identify whether the enclosure is wall-mounted, floor-standing, or integrated into a larger lineup. Any required separation, service access, or arc-flash mitigation provisions should be established by the design team.

Address Harmonics at the System Level

Variable-frequency drives draw non-linear current, so harmonic effects merit review alongside the drive selection. Relevant inputs include the number and size of drives, transformer impedance and capacity, utility characteristics, existing non-linear loads, and the sensitivity of connected equipment. A single panel cannot be evaluated in isolation when several loads share a source.

Depending on the study and project criteria, mitigation may involve line reactors, filters, or other measures, but no method suits every system. Specify applicable limits and any required analysis or monitoring. The responsible engineer should assess expected distortion and confirm compatibility with the utility and facility distribution system.

Plan Cooling Around Heat and Site Conditions

Drive losses and other panel components generate heat, while ambient temperature, altitude, enclosure size, and installation clearance affect heat removal. Provide expected operating conditions and any nearby heat sources. The design must account for the selected drive’s thermal requirements and the enclosure’s actual installation environment, rather than relying on a generic ventilation assumption.

Cooling may use natural airflow, fans, heat exchangers, or air conditioning where the project conditions call for them. Each approach has maintenance and environmental implications, including filter access and exposure to contaminants. Confirm acceptable noise, room temperature limits, airflow paths, and whether cooling equipment needs alarms or status contacts.

Define the Motor Cable Interface

Motor cable length and routing can influence reflected-wave voltage, insulation stress, electromagnetic interference, and drive operation. Share approximate route length, conductor type and size, shielding, conduit arrangement, and whether cables run near instrumentation or communications wiring. Long leads or fast-switching drives may call for application-specific output measures.

Clarify the motor terminal arrangement, grounding and shield-termination method, and responsibility for field wiring. Output reactors or dv/dt filters may be considered when supported by the drive manufacturer’s guidance and engineering review. Confirm cable and motor compatibility, grounding practices, and any applicable installation requirements before releasing the panel interface.

Coordinate Protection, Bypass, and Controls

Document the intended disconnecting means, branch-circuit protection, control power, and required interlocks. If bypass operation is requested, define its purpose and sequence: bypass arrangements can change motor starting behavior and do not provide variable-speed operation while the motor is bypassed. Confirm whether maintenance isolation or redundant operation is part of the design basis.

List local and remote controls, status indications, fault outputs, communication protocols, and integration points with the plant control system. Provide control schematics or an I/O list when available, and identify the operating modes and permissives. Protection and coordination should be reviewed for the actual source, motor, and downstream equipment.

Prepare Information for a Quote

A useful quote package includes motor schedules, one-line diagrams, control narratives, load and duty data, source voltage, fault-current information, and the applicable project specifications. Add enclosure location and environmental conditions, requested accessories, cable-route estimates, and preferred documentation. Note required inspection or testing provisions without assuming a particular approval or test result.

Identify delivery destination, site constraints, project milestones, and any specified submittal format. We build new equipment in the U.S. using American components, offer custom fabrication, and ship nationwide; configuration and schedule depend on the project scope. Complete inputs help establish a practical panel arrangement and clarify open engineering decisions.

Verify the Complete Installation

Panel design is only one part of a drive installation. Confirm upstream transformer and feeder capacity, protective-device coordination, grounding, ventilation, motor suitability, and cable installation with the responsible engineer. Utility requirements and the authority having jurisdiction may also affect the final design, installation, or required documentation.

Before release, reconcile the panel drawings with field conditions, including clearances, conduit entry, service access, and control-system interfaces. Confirm who supplies and installs field cables, performs startup, and verifies settings. These checks help ensure the delivered configuration matches the application rather than relying on assumptions about site conditions or standard options.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields