Choose the protection point in the distribution system
An SPD’s location affects which portion of a facility it protects and how its leads can be routed. A device installed at the service entrance addresses incoming surges at the main distribution point; a downstream location can serve a particular panel or sensitive load. These positions are not interchangeable.
For a switchboard quote, identify the intended installation point and the equipment or circuits to be protected. Provide a one-line diagram showing the service, main device, bus arrangement, and downstream distribution. The responsible engineer should confirm whether switchboard-mounted protection fits the facility’s protection plan.
Match the SPD to the actual system voltage
Voltage selection requires more than a nominal number. The engineer should confirm the system’s nominal voltage, phase, frequency, grounding method, and relevant operating conditions, then select an SPD configuration compatible with those conditions. An unsuitable voltage or grounding match can impair protection or create an equipment issue.
Send the service and distribution voltage details with the one-line diagram, including any separately derived systems or transformers affecting the point of connection. Do not assume a device suitable for one voltage or grounding arrangement will suit another. Final compatibility must be verified for the specific design.
Coordinate disconnecting means and overcurrent protection
An SPD may require a specified disconnecting means or overcurrent protective device, depending on its design, installation instructions, and applicable code requirements. The switchboard configuration must provide an appropriate connection and account for the selected device’s required protection. Confirm whether the SPD is integral to a section or mounted in a separate enclosure.
Provide the preferred SPD model or its electrical and installation requirements when available, along with the proposed switchboard main and feeder details. The design team should verify the disconnecting arrangement, conductor routing, and available space. Requirements must be checked for the chosen build rather than treated as standard across all configurations.
Plan placement, lead routing, and service access
Physical placement matters because connection length and routing influence the installed protection arrangement. A compact, direct connection may be preferable, but bus layout, barriers, wiring space, and the switchboard’s construction can constrain location. Maintenance access and visibility also deserve attention when selecting a mounting position.
Identify site access limits, room clearances, cable-entry direction, and any preferred SPD position on the switchboard lineup. Share enclosure and layout requirements early, especially where the equipment must fit an existing electrical room. Custom fabrication can address project-specific arrangements, subject to engineering review and the selected equipment’s constraints.
Coordinate protection across multiple levels
Facilities may use protection at the service entrance and at downstream distribution points. Coordination should be considered across those devices, including their intended roles and the equipment they serve. Adding an SPD to a switchboard does not, by itself, establish a complete protection strategy or guarantee coordination with devices elsewhere.
Provide details of existing or planned downstream SPDs, protective devices, and sensitive loads. The responsible engineer should review manufacturer information and the overall design to determine whether device selection and placement support the intended approach. Utility characteristics, site conditions, and applicable requirements may also affect the decision.
Distinguish switchboard standards and equipment classes
A low-voltage switchboard built to UL 891 is distinct from low-voltage switchgear built to UL 1558. These are different equipment categories, and the applicable construction standard depends on the project specification and design. Neither designation should be used as a substitute for confirming the actual assembly and its required ratings.
Medium-voltage equipment is a separate category; UL 891 does not cover medium- or high-voltage equipment. If the project includes medium-voltage distribution, identify the voltage class and equipment scope separately. Confirm required standards, ratings, and approvals for the specific build with the responsible engineer and the authority having jurisdiction.
Prepare complete information for a build quote
A useful request includes the one-line diagram, system voltage and grounding, main and feeder requirements, available fault-current information, installation location, and desired SPD point. Include enclosure conditions, cable-entry preferences, space constraints, and project specifications. If a preferred SPD is named, provide its documentation and connection requirements.
These details allow the manufacturer to review the requested switchboard configuration and identify open engineering questions before fabrication. State whether the scope includes only the switchboard assembly or associated distribution equipment, and note delivery destination and schedule needs. Ratings, listed status, and final configuration are confirmed for the specific design, not presumed.
Review the final design before release
Before release, compare the switchboard submittal with the project one-line diagram, specifications, SPD documentation, and site conditions. Resolve discrepancies in voltage, grounding, device location, disconnecting means, and conductor routing. The responsible engineer should confirm design intent, while the utility and AHJ should be consulted where their requirements apply.
The manufacturer builds new switchboards in the United States using American components and can provide custom fabrication for project requirements. Short lead times and nationwide shipping are available, with timing dependent on the final configuration and project conditions. Confirm scope, schedule, and shipping details with the manufacturer before ordering.