Request a Quote

Power distribution equipment

Medium-Voltage Motor Control Centers

Specify a new medium-voltage motor control center around the motor duty, system conditions, switching method, and protection strategy. Review key engineering inputs and configuration choices before requesting a project quote.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Switchgear cabinets in an electrical equipment room
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Match the lineup to the motor application

Medium-voltage motor control centers group motor starter units and associated distribution equipment in a coordinated lineup. They can suit facilities with multiple medium-voltage motors, such as pumps, compressors, fans, and process machinery. The right arrangement depends on the plant’s operating needs, electrical system, and maintenance practices—not simply motor voltage.

Begin by identifying each motor’s rated voltage, horsepower, full-load current, starting frequency, load characteristics, and required operating sequence. Note whether motors run continuously, cycle frequently, or start under load. These details inform starter selection and protection coordination; confirm application assumptions with the responsible engineer and motor manufacturer.

Select a starting and switching approach

Starter configuration affects inrush current, acceleration time, mechanical stress, and the demands placed on the electrical source. Across-the-line starting may be appropriate in some systems, while reduced-voltage methods may be considered where the motor, driven equipment, and available fault and starting capacity support them. Verify suitability for the specific duty.

Switching equipment may use vacuum contactors or circuit breakers, depending on the lineup design, system requirements, and protection scheme. These devices are not interchangeable choices by default. Establish how often switching occurs, what isolation is needed for service, and how the equipment must coordinate with upstream protective devices.

Define system voltage and fault conditions

Provide nominal system voltage, grounding method, frequency, and available short-circuit current at the proposed lineup location. Also identify the source transformer data and relevant upstream protective-device settings when available. These inputs help determine equipment ratings and coordination needs; they should be confirmed from current utility or facility engineering information.

Medium-voltage equipment has distinct construction and application requirements from low-voltage switchboards and switchgear. UL 891 applies to switchboards, not medium-voltage motor control centers. The applicable construction standard, listing or certification requirements, and project specifications must be established for the actual equipment and jurisdiction.

Build a protection scheme around each motor

Motor protection may address overload, short circuit, ground fault, phase loss, locked rotor, or other conditions relevant to the application. The selected functions and settings depend on motor data, starting profile, system grounding, and coordination objectives. Avoid assuming that one relay package or setting set suits every starter in a lineup.

Share motor nameplate information, starting curves if available, control requirements, and upstream and downstream device data for engineering review. Confirm whether protection must interface with plant monitoring, a distributed control system, or a safety system. The responsible engineer should review coordination, relay logic, and settings before release and commissioning.

Plan lineup arrangement and service access

A lineup’s physical arrangement should reflect the one-line diagram, cable entry direction, room layout, and planned expansion. Identify required starter quantities, spare spaces, incoming sections, bus connections, and any auxiliary compartments. Confirm dimensions, access clearances, equipment-room conditions, and handling routes against the project site before fabrication.

Consider how operators will isolate a motor, access control components, and perform inspection or testing under the facility’s safety procedures. Specify any preferred compartment arrangement, labeling conventions, and door or interlock requirements for review. These are project decisions, not universal features, and must align with the equipment design and applicable codes.

Coordinate controls and plant interfaces

Document the intended control philosophy for each motor: local or remote operation, permissives, interlocks, status points, alarms, and trip indications. Identify control voltage and the interface to existing systems. Provide relevant I/O lists, communication requirements, and sequence descriptions so the proposed starter controls can be evaluated against plant operation.

Clarify whether the project needs metering, protective relaying communications, or integration with a supervisory platform, and identify the protocols or interface standards specified by the facility. Confirm who supplies field devices, wiring beyond the lineup, and programming. Resolve interface boundaries early to reduce gaps between equipment scope and installation responsibilities.

Prepare complete information for a quote

A useful quote request includes a current one-line diagram, motor schedule, system voltage and fault data, grounding details, project specifications, and applicable drawings. Include the number and type of starters, operating duty, control expectations, environmental conditions, and delivery constraints. Mark unresolved items clearly so they can be treated as questions, not assumptions.

Also identify the installation location, cable routing preferences, required documentation, inspection or certification expectations, and any project-specific testing or witness requirements. A manufacturer can review these inputs, identify information gaps, and develop a configuration for discussion. The responsible engineer, utility, and authority having jurisdiction should verify applicable design and approval requirements.

Engineer a new lineup for the project

New medium-voltage motor control centers are manufactured to the project’s defined electrical, mechanical, and control requirements. U.S. manufacturing with American components and custom fabrication can support tailored lineup arrangements. Short lead times and nationwide shipping are available as part of supply planning, with timing and logistics confirmed for each order.

Before release, align the approved drawings, motor and protection data, interface scope, and site constraints among the manufacturer, engineer, contractor, and owner. Changes to motor duty, fault data, or control sequences can affect design decisions. A disciplined review gives the project team a clearer basis for procurement, installation, and startup planning.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields