Request a Quote

Power distribution equipment

Ground-Fault Protection Switchboards

Specify a ground-fault protection switchboard around the system voltage, grounding method, service arrangement, and applicable code requirements. We build new, custom-fabricated equipment in the U.S. with American components and ship nationwide.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Three gray switchgear cabinets on wooden pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start with the service and code basis

Ground-fault protection is not a one-size-fits-all switchboard feature. Its applicability and design depend on the installation, service characteristics, adopted electrical code, and project requirements. For a new equipment inquiry, identify whether the switchboard is service equipment or downstream distribution, and provide the system voltage, phase, wire configuration, and intended installation.

At service equipment, the responsible engineer should determine which requirements apply under the code adopted by the local jurisdiction, including applicable thresholds and exceptions. Confirm the utility service arrangement and consult the authority having jurisdiction (AHJ). Do not assume that a particular sensing scheme or trip setting is required solely because a switchboard serves a large load.

Define what the protection must detect

Ground-fault protection generally detects current returning through an unintended ground-fault path and initiates operation of a protective device. The sensing method must suit the conductor arrangement and grounding design. A quote should state whether protection is needed at the service main, a feeder device, or multiple points, and what portions of the distribution system each device is intended to protect.

Ask the engineer to document the grounding method, including any neutral-to-ground bonding locations, and identify which conductors pass through or are monitored by each sensor. Neutral treatment is especially important on grounded systems: incorrect sensor placement or an unaccounted parallel return path can affect detection. Final sensor arrangement must be reviewed against the actual one-line and equipment layout.

Select a sensing and trip arrangement

Depending on the design, a ground-fault function may be incorporated in a compatible circuit-breaker trip unit or implemented through a separate relay, sensors, and a means of tripping the protective device. The choice depends on available devices, required functions, control power, space, and the approved design—not on a universal switchboard configuration.

Specify the desired functions and interfaces, such as indication, alarm contacts, remote status, or trip outputs, when these are required. Confirm control voltage and whether the project calls for adjustable pickup and delay. These details must be checked for compatibility with the selected protective device and the manufacturer's available equipment; they should not be treated as standard features unless confirmed.

Coordinate protection with downstream devices

Where multiple protective devices are involved, the engineer should evaluate selective coordination and the intended sequence of operation. Ground-fault pickup and time delay choices can affect whether an upstream or downstream device responds first. Settings must be based on the system study, device characteristics, and applicable requirements rather than copied from another installation.

Provide available short-circuit current, protective-device types and ratings, and existing or proposed settings for devices that interact with the switchboard. Coordination objectives, including any required study criteria, should be identified early. The responsible engineer should verify that the proposed arrangement is consistent with the overall protection scheme and utility conditions.

Match the switchboard construction to the application

UL 891 applies to low-voltage dead-front switchboards; it is not a medium- or high-voltage standard. If the project requires a UL 891 switchboard, identify the desired bus, mains, feeder devices, metering, enclosure, and service configuration. Ground-fault protection must be evaluated as part of the specified assembly and selected devices.

Do not substitute low-voltage switchgear terminology for switchboard requirements. UL 1558 low-voltage switchgear is a distinct equipment category, while medium-voltage equipment requires a different design basis and standards appropriate to its voltage class. State the project’s equipment category and voltage clearly so the manufacturer can assess the requested configuration accurately.

Plan for installation and system interfaces

A protective scheme must fit the physical and electrical installation. Provide available room dimensions, cable entry direction, conductor sizes where known, mounting conditions, and any restrictions on access or clearances. Identify interfaces to building monitoring or control systems, and clarify whether external trip, alarm, or communications connections are part of the design.

For replacement planning at a facility, describe the existing system and the intended new installation without assuming reuse or compatibility of old components. Confirm fault-current data, grounding details, utility requirements, and the AHJ's expectations. The responsible engineer should review the switchboard location, disconnecting means, and operating procedures as part of the complete installation.

Prepare complete information for a quote

A useful quote package includes a one-line diagram, load and feeder schedule, system voltage and frequency, grounding method, available fault current, and project specifications. Include the service entrance details, requested ground-fault functions, device preferences if established, and any required coordination or arc-flash study inputs. Mark items that remain subject to engineering review.

Also provide the project location, indoor or outdoor application, enclosure and access constraints, cable or bus connections, metering needs, and requested delivery schedule. Identify applicable specifications and submittal requirements. These inputs help establish a practical scope for custom fabrication; final ratings, device availability, and construction details require project-specific review and confirmation.

Build around confirmed project requirements

We manufacture and supply new switchboards in the United States using American components, with custom fabrication for project requirements and nationwide shipping. Short lead times may be available, but schedule depends on the approved design, component selection, and current production conditions. Share the required in-service date so timing can be reviewed rather than presumed.

Before release, the responsible engineer should verify the final drawings, grounding and sensing arrangement, protective-device functions, and coordination assumptions. The utility and AHJ should be consulted where their requirements apply. A ground-fault protection switchboard is configured for a defined electrical system; equipment details and any applicable listing or approval must be confirmed for the specific build.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields