Request a Quote

Power distribution equipment

New Switchgear with Spare Feeders

Plan spare feeders as part of a complete new switchgear lineup, not as empty spaces alone. Coordinate future load assumptions, bus ratings, protective devices, and expansion interfaces before requesting a quote.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Electrical distribution lineups in a spacious equipment facility
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

A Spare Feeder Is More Than an Empty Space

A spare feeder position reserves a place in a new lineup for a future circuit, but the opening alone does not establish that the equipment can serve any later load. The feeder compartment, bus, protective device, cable terminations, and available fault-current rating must all suit the intended application.

Begin with a realistic description of expected additions: load type, voltage, phase, estimated demand, motor starting or inrush characteristics, and likely installation timing. If the future load is uncertain, identify a reasonable planning range rather than treating the position as universally usable.

Match Feeder Count to Likely Growth

Decide how many future circuits merit dedicated positions by reviewing facility plans, process changes, tenant requirements, and the consequences of later adding another section. A single large anticipated load may need a different compartment and device arrangement than several smaller branch feeders.

The lineup layout should identify active feeders, spare positions, and any spaces reserved for later equipment. Confirm section width, front access, cable entry, and room clearances against the electrical room and installation route. A planned position is useful only if it can be reached and connected.

Check Bus Capacity Against the Load Plan

Spare feeder positions do not create additional bus capacity. The main bus and any distribution bus must be evaluated against present and projected demand, load diversity, operating conditions, and the design basis used for the installation. Confirm the applicable continuous-current ratings and temperature or enclosure considerations for the specified equipment.

Share the service voltage, source configuration, calculated load, anticipated growth, and any utility or project limits when developing the lineup. The responsible engineer should determine demand and loading assumptions. Avoid choosing a bus rating solely by counting spare compartments or adding nameplate feeder ratings together.

Specify the Future Feeder Device

A future feeder may require a circuit breaker or another specified protective device, with frame, trip, poles, and adjustment range selected for the circuit. Those details depend on the expected load, conductors, protection study, coordination requirements, and the equipment's available fault-current conditions.

For each planned spare, indicate whether the device is to be installed initially, supplied as a future provision, or left as an empty compartment. Confirm the scope carefully: a compartment prepared for later work is not the same as a furnished, wired, tested feeder with defined protective settings.

Verify Ratings and Protection Together

Device interrupting capability and the switchgear or switchboard short-circuit rating must be appropriate for the available fault current at the installation point. Confirm system voltage, source information, transformer data, utility contribution, and any generator or parallel-source operation needed for the fault-current assessment.

Protection settings and selectivity should be reviewed with the complete system, including upstream devices and downstream loads. Specify the required studies, documentation, and coordination objectives for the project. Final selection and settings should be checked by the responsible electrical engineer and, where applicable, the utility and AHJ.

Design Expansion Interfaces Before Ordering

If future work may extend the lineup, define the intended expansion interface at the outset. Relevant details can include end-of-line arrangement, bus connection provisions, barriers, enclosure construction, access, and how a later section would connect without conflicting with existing conductors or room constraints.

Do not assume a spare compartment guarantees that another section can be added or that the lineup can be expanded while energized. Confirm the manufacturer's proposed configuration, future connection method, installation clearances, outage expectations, and any field work required. Expansion planning remains subject to engineering review and site conditions.

Choose the Equipment Standard for the Application

Identify whether the project calls for a UL 891 switchboard or UL 1558 low-voltage switchgear. These are distinct equipment categories, and the appropriate construction depends on the system design, application, specified construction, and project requirements. Medium-voltage equipment is a separate category with its own applicable standards.

For a quotation, provide the one-line diagram, equipment specification, voltage and system grounding, source and fault-current information, feeder schedule, enclosure and access requirements, and desired spare-feeder scope. Include drawings or notes that define future sections, bus provisions, and any owner standards to be addressed.

Request a Buildable, Clearly Scoped Lineup

A useful quotation distinguishes installed feeders from spare positions and states the proposed bus rating, device provisions, lineup arrangement, and expansion interfaces for review. Include delivery destination, schedule constraints, site access, and required submittal documents so the proposed new equipment can be evaluated against the project.

We manufacture new switchgear and power distribution equipment in the United States using American components, with custom fabrication and nationwide shipping. Share project drawings and requirements for a configuration review. Confirm final design details with the responsible engineer, utility, and AHJ where applicable before release.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields