Request a Quote

Power distribution equipment

Main Breaker Switchboards

Configure a new main breaker switchboard around the service entrance, feeder layout, and protective-device coordination your project requires. Our U.S.-built equipment is custom fabricated for Ohio and nationwide applications.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Electrical distribution lineups in a spacious equipment facility
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

How the Main Breaker Shapes the Distribution Layout

A main breaker switchboard places a circuit breaker at the incoming supply, ahead of downstream feeder devices. This arrangement gives the distribution assembly a single main overcurrent protective device and a means of disconnect, subject to the applicable design and installation requirements. It differs from a main-lug-only arrangement, where upstream protection and disconnecting provisions are handled elsewhere.

The main device, bus arrangement, and feeder sections must be developed together rather than selected independently. Confirm the source, service voltage, phase, wire configuration, required feeder count, and anticipated loads. The responsible electrical engineer should establish the one-line diagram and clarify whether the assembly serves as service equipment or is installed downstream of another disconnect.

Establish the Application and Applicable Equipment Standard

For many low-voltage distribution applications, UL 891 switchboards are a relevant equipment category. UL 891 applies to switchboards; it is not a standard for medium- or high-voltage equipment. Where the project requires low-voltage switchgear, UL 1558 is a distinct category with different construction and evaluation considerations. Medium-voltage lineups require their own applicable equipment basis.

Identify the project’s required equipment type early, including the specified standard, nominal voltage, and installation role. Requirements may differ among utility service, a facility distribution point, and a downstream lineup. The engineer, utility, and authority having jurisdiction should review the proposed arrangement where applicable; do not assume that a standard or configuration suits every installation.

Coordinate Main and Feeder Protective Devices

Coordination depends on the protective-device types and settings, available fault current, conductor characteristics, and the system’s operating requirements. A main breaker does not automatically coordinate selectively with every feeder breaker. Review time-current behavior across the relevant current range, including whether the project calls for selective coordination under a particular code provision or operational objective.

Provide the engineer’s coordination study or specified device settings when available, along with breaker manufacturer and frame or trip requirements where the design establishes them. Confirm any desired adjustable functions, ground-fault protection, and zone-selective features as project requirements rather than assumed standard features. Final selection and settings must be checked against the system study and applicable rules.

Verify Short-Circuit Duties and Device Ratings

The available fault current at the switchboard affects the required short-circuit ratings of the assembly and its protective devices. Confirm the utility contribution, transformer data, conductor lengths and sizes, and any upstream impedance information needed for the calculation. Also establish whether the design specifies an interrupting rating, short-circuit current rating, or other rating basis for the proposed equipment.

Do not treat a breaker’s interrupting rating as interchangeable with the switchboard assembly rating. Any series rating or tested combination must be supported by the applicable documentation and permitted for the specific application. The responsible engineer should verify the calculated duty at the installation point and confirm that the selected devices and assembly meet project requirements.

Plan Feeder Sections, Terminations, and Future Needs

A useful feeder schedule identifies each load, breaker pole count, required trip characteristics, conductor material and size, and termination arrangement. Note spare spaces separately from installed feeder devices, and state any allowance for future circuits or anticipated load growth. These choices affect section layout, bus design, cable access, and the dimensions needed for a workable installation.

Document top or bottom cable entry, conduit landing area, lug requirements, and any limits on conductor bending space. Confirm whether feeders leave through the top, bottom, or another project-specific route, and whether parallel conductors are needed. A clear schedule helps the manufacturer develop a buildable arrangement while leaving final conductor and overcurrent-device design to the responsible engineer.

Match the Enclosure and Site Conditions

Enclosure selection should reflect the actual installation location, exposure, and access conditions. Specify indoor or outdoor placement, the required enclosure type, room or pad constraints, ambient conditions, and any known dust, moisture, or corrosive exposure. Confirm working clearances, door swing, equipment orientation, and the route from the delivery point to the final position.

Construction details such as dimensions, finish, compartment arrangement, and provisions for incoming or outgoing cables should be confirmed for each project. Seismic, elevation, special environmental, or restricted-access requirements may also affect the design and must be identified in the specification. The equipment design should be checked against site conditions and applicable code by the project team.

Define Service, Metering, and Control Requirements

Service details determine how the main breaker switchboard connects to the source and how the incoming conductors land. Provide the utility’s service requirements, grounding and bonding scheme, neutral configuration, and any metering or compartment requirements. Utility rules can govern service equipment details, so confirm them before the layout is finalized rather than relying on a generic arrangement.

List control power, indication, communications, and accessory needs only when required by the project. Examples may include status contacts, shunt trip, undervoltage release, or metering provisions, subject to compatibility and specification. State interfaces with generators, transfer equipment, or building controls where relevant; confirm protection, wiring, and operational sequences with the design team.

Prepare a Complete, Reviewable Quote Package

A quote request is more useful when it includes the one-line diagram, equipment specification, feeder schedule, available fault-current data, and the required equipment standard. Add voltage, phase, main-device requirements, enclosure and entry details, dimensions or access limits, and project quantity. Identify the drawing review process, requested submittals, delivery destination, and any schedule milestones.

Our company manufactures and supplies new switchboards built in the United States with American components, with custom fabrication and nationwide shipping for Ohio and other U.S. projects. Lead times depend on scope, component availability, and approvals. Send project-specific requirements for review; confirm final design details with the responsible engineer, utility, and AHJ as applicable.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields