Request a Quote

Power distribution equipment

Double-Ended Switchgear

Specify a new double-ended lineup around its sources, tie arrangement, protection study, and intended operating modes. Our U.S. team builds custom switchgear and distribution equipment for Ohio projects and nationwide shipment.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Motor control center lineup inside an industrial building
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

What a Double-Ended Lineup Does

Double-ended switchgear divides a distribution lineup into two sections, each normally supplied by a separate source, with a bus tie connecting the sections. The arrangement can support load transfer when a source or section is unavailable, but continuity depends on the actual source capacity, protection scheme, switching procedure, and loads served.

A project may use utility services, transformers, generators, or another engineered combination as sources. These are not interchangeable assumptions: available fault current, grounding, voltage, source impedances, and permitted operating conditions shape the design. Start by documenting what each source can supply and which loads must remain energized during an outage or maintenance event.

Choose the Equipment Class First

Low-voltage double-ended lineups may be built as switchboards or low-voltage switchgear, depending on application and required construction. UL 891 applies to switchboards; UL 1558 applies to low-voltage switchgear. The responsible engineer should establish the applicable equipment standard, service conditions, ratings, and specifications rather than treating the terms as equivalent.

For medium-voltage distribution, the equipment class, insulation system, switching devices, protection, and applicable standards differ from low-voltage assemblies. UL 891 does not cover medium- or high-voltage equipment. Confirm nominal and maximum system voltage, utility requirements, installation environment, and the project’s governing specifications before selecting a lineup family or requesting pricing.

Define Sources, Sections, and Tie

A typical arrangement has an incoming device for each source, a bus section serving assigned feeders, and a tie device between sections. The physical lineup may place the tie centrally or use another arrangement driven by room layout, cable entry, maintenance access, and feeder distribution. One-line diagrams should show source boundaries, metering, grounding, and load allocation.

Decide whether each section must carry its normal load only or support designated loads from the opposite source after transfer. Check bus and device ratings against the resulting current, including credible operating combinations. Provide source and transformer data, feeder schedules, cable or bus connections, and any space, access, or future-expansion constraints for configuration review.

Select the Intended Operating Modes

Common operating modes include both sources serving separate sections with the tie open, one source feeding both sections through a closed tie, or a planned transfer from a failed source to the healthy source. The preferred mode depends on source capacity and the owner’s operating philosophy; no lineup should be assumed to support every mode without engineering review.

Specify whether transfers are manual, electrically operated, automatic, or initiated by a supervisory system. Identify the conditions that permit or block a transfer, including source status, voltage, phase relationship, and load-shedding steps. If paralleling sources is prohibited, define controls and interlocking that prevent an unintended parallel condition, subject to the approved design.

Coordinate Protection Across Both Sources

Protection must be evaluated for each source and each permitted lineup state. A bus tie changes the available fault-current paths and may alter the current seen by incoming and feeder devices. A settings study should examine source contribution, device interrupting and withstand capabilities, ground-fault protection where applicable, and coordination with upstream utility or transformer protection.

Provide the latest short-circuit and coordination studies, device types and settings, transformer impedances, grounding method, and utility fault-current information when available. Confirm whether arc-flash analysis, zone-selective interlocking, differential protection, or other functions are specified. These are project decisions, not features to presume; the responsible engineer must validate the complete protection scheme.

Plan Interlocks and Transfer Logic

Mechanical or electrical interlocks can restrict device combinations, while control logic may supervise permissives and transfer sequences. The exact scheme should reflect the operating modes and whether sources can ever be paralleled. Describe normal device positions, failure response, local and remote controls, alarms, and any required sequence of operations so the builder can coordinate compartments and control wiring.

Automatic transfer introduces additional questions: what initiates transfer, how loss of source is verified, whether transfer is open-transition, and what happens if the alternate source is unavailable. Include generator start and load acceptance requirements when relevant. Review control power, communications, status points, and reset behavior with the project team before finalizing drawings.

Check Ratings, Space, and Connections

Specify system voltage, continuous current, short-circuit or withstand requirements, frequency, environmental conditions, and any required service entrance or metering provisions. The applicable ratings must be established from system studies and project documents, not inferred from a product label or a typical lineup. Confirm whether neutral treatment, ground-fault functions, or special incoming arrangements are required.

Room dimensions, working clearances, equipment access, cable bending space, top or bottom entry, and shipping limitations can affect lineup sections and construction. Identify indoor or outdoor placement, ambient conditions, seismic or other site criteria, and finish requirements where applicable. Any requested approvals, tests, or construction details should be confirmed for the specific build and specification.

Prepare a Complete Quote Package

For a useful quote, send the one-line diagram, equipment specification, source and transformer data, feeder schedule, load summary, protection studies, and required operating sequence. Add voltage and current ratings, fault-duty requirements, connection preferences, metering and control scope, site conditions, and delivery destination. Mark open decisions clearly so they can be resolved before design release.

Our U.S. manufacturing team builds new switchgear and power distribution equipment with American components, including custom-fabricated configurations for projects in Ohio and nationwide. Short lead times are offered, but schedule depends on scope, component availability, approvals, and design completion. Have the responsible engineer, utility, and AHJ review applicable requirements and project documents.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields