Request a Quote

Serving Ohio

Akron Stormwater Pump Station Transfer

For Akron stormwater pump projects, transfer equipment must coordinate utility service, standby generation and pump controls as one engineered system. We build new switchgear and distribution equipment to project specifications, with interfaces confirmed against the station’s electrical design.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Electrical distribution lineups in a spacious equipment facility
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Define the station’s operating sequence

Start with the pump station’s intended behavior when normal utility power is lost. Confirm which pumps must operate, whether they start in stages, and how controls prioritize duty and standby units. The transfer arrangement should support that sequence without assuming every pump needs to run simultaneously.

Document normal and emergency operating modes, including any minimum pumping capacity required during an outage. Identify alarms, remote status points, control-power sources and operator actions. The responsible engineer should coordinate these requirements with the facility owner and controls integrator before selecting equipment or requesting a quotation.

Choose the source-transfer arrangement

Automatic transfer equipment can switch a defined load between utility and generator sources, but its configuration depends on the service and distribution design. Confirm whether transfer occurs at the station service entrance, a downstream distribution point, or through another engineered arrangement. These choices affect feeder routing, protection and maintainability.

Specify whether the system uses an open-transition transfer, another approved transition method, or a manual operating step. The acceptable sequence depends on utility rules, generator characteristics and connected loads. Transfer equipment must prevent unintended source paralleling unless the design specifically permits it and the required controls and approvals are provided.

Coordinate generator connection details

Generator connection requirements begin with the generator’s electrical data and the station load profile. Provide voltage, phase, frequency, available output, grounding arrangement and connection method, along with the loads expected to start during an outage. Confirm whether a permanent generator or temporary connection point is part of the project scope.

Starting current, motor acceleration and the order in which pumps restart can influence generator capacity and transfer settings. Share motor data, drive information and control sequences with the generator supplier and electrical engineer. Do not size the transfer equipment or assume a generator rating from pump nameplate horsepower alone; review the complete load study.

Match equipment to voltage and application

The distribution equipment must match the station’s service voltage, current requirements, available fault current and installation conditions. For low-voltage distribution, UL 891 applies to switchboards; UL 1558 applies to low-voltage switchgear. Neither standard covers medium- or high-voltage equipment, which requires a separate application-specific design basis.

Where a project includes medium-voltage service, specify that equipment separately and coordinate it with the utility, protection scheme and downstream transformer or distribution system. Confirm the requested construction, enclosure, access, bus arrangement and termination details for each assembly. Applicable listings and ratings depend on the final design and must be verified for the build.

Integrate pump controls and protection

Pump control interfaces should be defined at the boundary between the transfer equipment, motor starters or drives, and station control system. Identify which device issues start commands, which provides overload and fault protection, and how permissives prevent an unsafe or unwanted restart after power returns.

List required hardwired contacts, communication interfaces, alarm points and control-power arrangements rather than assuming a standard signal package. Confirm how the controls respond to low voltage, phase loss, generator warm-up, transfer delay and restoration of utility power. The controls integrator and responsible engineer should resolve interlocks and restart logic before fabrication.

Check protection, grounding and site constraints

Review coordination and fault-duty requirements across utility, generator, transfer equipment and pump feeders. Utility and generator sources may contribute different fault currents, which can affect protective-device selection and settings. Confirm the available fault current, equipment interrupting or withstand requirements, grounding method and selective-coordination objectives with the responsible engineer.

Akron project conditions also need site-specific review: indoor or outdoor placement, environmental exposure, access for servicing, conduit entry, working clearances and the station’s existing equipment interfaces. Confirm applicable utility requirements and local authority having jurisdiction review. Do not assume an enclosure rating, environmental feature or protection setting without project documentation.

Prepare a complete quote package

A useful quotation package includes one-line diagrams, load schedules, service and generator data, pump motor information, control schematics, fault-current and coordination studies, and the specified equipment standards. Include enclosure and layout constraints, cable entry preferences, required metering, communication points and any project documentation or submittal requirements.

Also identify the requested scope boundaries: equipment furnished, field-installed wiring by others, generator connection hardware, startup responsibilities and controls integration. Clearly mark open decisions and required alternates. This lets the manufacturer assess custom fabrication needs and provide a proposal based on the actual design rather than unsupported assumptions about ratings, accessories or interfaces.

Build and deliver for the project schedule

We manufacture new switchgear and power distribution equipment in the United States using American components, and can custom-fabricate assemblies for defined project requirements. Short lead times may be available, but schedule depends on approved drawings, component availability, engineering scope and the final configuration; confirm the project-specific delivery schedule with the quotation.

We supply equipment to customers in Akron and nationwide. Before release, review drawings and interface details with the electrical engineer, generator supplier, controls integrator, utility and AHJ as applicable. Provide the shipping destination, receiving constraints and installation sequence so equipment configuration and delivery planning reflect the station’s actual project needs.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields