Request a Quote

Manufacturing capabilities

Arc Flash Study Design Inputs

A useful arc flash assessment starts with a current electrical model, not an equipment label alone. Gather one-lines, device settings, source characteristics, and field details so the engineer can define the study scope and identify missing inputs.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Switchgear cabinets with breakers on warehouse pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start with the Study Boundary

Before collecting records, confirm which facilities, systems, and operating configurations the assessment must cover. Define the service entrance, distribution levels, equipment included, and any tie points or alternate sources. The engineer needs a clear boundary to determine which upstream and downstream data affect modeled incident energy and equipment labels.

Also identify the assessment purpose and applicable project criteria, such as an update after renovations, a new installation, or a broader safety review. Confirm the responsible engineer, facility contacts, and available field access. These decisions shape the data request; they do not establish a particular result or guarantee that records alone are sufficient.

Provide Current One-Line Diagrams

Provide the latest electrical one-line diagrams in a legible, editable format when available, along with revision dates and drawing numbers. Show utility service, transformers, generators, motors, switchboards, switchgear, panelboards, bus ties, and protective devices in their actual sequence. Include nominal voltages and equipment identifiers that match field labels.

Mark known changes that are absent from the drawings, including added loads, replaced breakers, modified conductors, or normally open ties. If no reliable one-line exists, provide sketches and equipment schedules as starting records, clearly identified as unverified. The study engineer should determine what field tracing or verification is required before modeling.

Document Utility and On-Site Sources

Request available utility fault-current or equivalent source data at the service point, including the stated voltage and the conditions or date associated with the values. Ask the utility or project engineer to clarify whether the figures represent maximum, minimum, or another operating condition. The study scope may require more than one source case.

For generators, photovoltaic systems, energy storage, or other on-site sources, collect manufacturer data and connection details available to the engineer. Record operating modes, transformer connections, and whether sources can operate in parallel with the utility. Do not substitute assumed values for missing data; identify gaps for engineering review.

Inventory Protective Devices and Settings

For each breaker, fuse, relay, and other protective device in the study path, provide manufacturer, catalog or type designation, frame and sensor information, trip-unit model, and available rating data. Capture actual adjustable settings, including long-time, short-time, instantaneous, and ground-fault functions where applicable, rather than relying only on nameplate maximums.

Include relay setting files or coordination study records when available, plus fuse class and size, breaker maintenance mode status, and notes about settings that differ by operating mode. Confirm settings against field conditions and identify devices whose records are uncertain. An engineer must judge which values are appropriate for each modeled case.

Capture Equipment and Conductor Details

Record equipment type, voltage, bus or panel identification, enclosure information, and available nameplate details for locations included in the assessment. Note manufacturer and model where readable, plus any documented interrupting or withstand ratings relevant to engineering review. Distinguish switchboards from low-voltage switchgear and medium-voltage equipment in drawings and records.

For conductors between modeled nodes, provide material, size, quantity per phase, length, insulation, and raceway or installation details when known. Transformer records should include kVA, primary and secondary voltages, impedance, connection, and grounding information. Missing or estimated data should be labeled explicitly for confirmation.

Describe Operating Configurations

List normal and credible alternate arrangements, such as open or closed ties, standby generator operation, parallel sources, and maintenance bypasses. Explain which configurations are permitted and how operators select them. If a transfer scheme or interlock changes the available source or device settings, provide control descriptions and relevant sequence documentation.

The engineer may need separate cases where source strength, equipment lineup, or protective-device settings change. Identify loads that are routinely disconnected and any temporary construction arrangements within the requested scope. Do not assume a single normal one-line represents every condition; ask the study engineer to define the scenarios to model.

Support Field Verification and Label Planning

Arrange safe access for qualified personnel to verify equipment identities, conductor routes, device settings, and nameplate information. Provide site safety rules, access restrictions, and a contact familiar with the electrical distribution system. Field observations can resolve drawing conflicts, but inspection methods and energized work decisions belong to qualified professionals under applicable procedures.

Clarify whether the project includes updated documentation, equipment labels, or only an engineering assessment. Confirm who will review findings and how discrepancies are handled. Label content, placement, and implementation should follow the engineer’s recommendations and applicable requirements; a study should not be represented as a substitute for safe work practices.

Prepare the Scope for Equipment Quotes

When an assessment identifies a need for new distribution equipment, provide the relevant study assumptions and design documents with the quote request. Specify system voltage, source arrangement, load requirements, physical constraints, connection details, and the intended equipment role. The responsible engineer should confirm the design basis and compatibility with existing protection and distribution.

Our U.S. manufacturing team builds new switchgear and power distribution equipment with American components, offers custom fabrication, short lead times, and nationwide shipping. Quote documents should identify requested standards and ratings for review, without assuming a particular listing or configuration. Have the responsible engineer, utility, and AHJ review applicable design requirements.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields