Request a Quote

Built for your application

Remote Oil and Gas Site Power

Remote oil and gas facilities need power distribution designed around available sources, changing loads, exposure, and limited site access. Explore switchgear considerations for resilient, monitorable installations.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Motor control center lineup inside an industrial building
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start with the Site’s Power Sources

An isolated well pad, gathering station, or compressor facility may receive power from a utility feeder, generators, or a combination that changes by operating condition. Start by documenting each source’s voltage, phase, frequency, grounding method, available fault current, and expected operating role. These details shape the distribution lineup and protection design.

For generator integration, confirm whether sources operate independently or are intended to transfer, parallel, or support separate loads. Those arrangements require different switching and control approaches; paralleling also brings synchronization and protection considerations. The responsible engineer should verify the one-line diagram and operating sequence with generator suppliers and the utility where applicable.

Choose Switching Around the Operating Sequence

A transfer scheme should reflect what operators need during a source interruption: automatic transfer, supervised manual transfer, or a defined sequence that sheds nonessential loads before restoring them. Confirm which loads must remain energized, acceptable interruption time, interlocks, and whether a return to the normal source should be automatic or operator-controlled.

New switchboards and low-voltage switchgear can be configured with incoming devices, feeder sections, metering, and control provisions suited to a project. UL 891 applies to low-voltage switchboards; UL 1558 applies to low-voltage switchgear. Neither standard should be treated as covering medium-voltage equipment, which requires a separate equipment and application review.

Account for Loads That Change with Operations

Remote sites can combine motors, variable-frequency drives, heaters, lighting, controls, communications, and temporary or seasonal loads. Provide load schedules with motor starting methods, duty cycles, demand assumptions, and planned expansions. Large motor starts can affect generator sizing and bus voltage, so review starting sequences and source capability rather than relying only on connected-load totals.

Separate critical process, safety-related, and convenience loads according to the project’s control philosophy and applicable requirements. Confirm which circuits require dedicated feeders, selective coordination, or load shedding, and identify any sensitive electronics or harmonic-producing equipment. These decisions influence breaker selection, metering, bus arrangement, and space reserved for future circuits.

Protect Equipment from Site Conditions

Environmental exposure varies widely between a heated electrical room and an outdoor enclosure near saltwater, dust, chemicals, or washdown activity. Specify installation location, ambient temperature range, altitude, condensation risk, corrosive agents, ingress protection needs, and any hazardous-area boundaries. Enclosure construction and internal components must suit the actual exposure, not an assumed generic oilfield environment.

Where flood risk, windborne debris, vibration, or temperature swings are concerns, describe them early and identify mounting, access, and ventilation constraints. Confirm whether equipment will be housed in a building, shelter, or outdoor cabinet, and how cables enter the lineup. The engineer, facility team, and authority having jurisdiction should resolve applicable code and site requirements.

Plan for Monitoring Beyond the Fence Line

Remote monitoring can help operators understand source status, breaker position, alarms, and electrical measurements without traveling to an isolated installation. Define which points matter, who receives alarms, and what response follows each condition. Monitoring provisions may include metering, status contacts, communications interfaces, and control wiring, subject to the selected equipment and project scope.

Identify the site’s supervisory system, communications protocol, network architecture, and available power for control equipment. Confirm cybersecurity responsibilities, signal ownership, and whether remote commands are permitted or monitoring is read-only. The switchgear supplier needs an I/O list and interface requirements; system integration, programming, and communications performance should be assigned explicitly among project parties.

Coordinate Protection and Fault Interrupting

Protection settings depend on source characteristics, fault-current studies, grounding, and the relationship between upstream and downstream devices. Provide utility data and generator reactance or protection information where available. The responsible engineer should evaluate interrupting ratings, short-circuit withstand, coordination, and arc-flash considerations for the actual system, including alternate-source operating modes.

A transfer between utility and generator can change available fault current and protective-device behavior. Check that the selected equipment and settings remain suitable in each intended configuration, and confirm any required maintenance or test provisions. Do not assume one set of study results applies to every source combination; final designs should be reviewed by the engineer and relevant utility.

Design for Access, Service, and Expansion

Long travel times make maintainability a practical design input. Discuss front or rear access, working clearances, lifting and replacement paths, spare feeder capacity, and the availability of qualified service personnel. Identify components that must be inspected or operated locally and consider how labels, drawings, and controls will support technicians unfamiliar with the site.

Future wells, process skids, or communications additions may change feeder counts and load levels. Establish which expansion assumptions are credible, then identify space and bus provisions for review rather than treating spare capacity as guaranteed. Site logistics also matter: provide transport limits, unloading equipment, installation sequence, and any constraints on shipment dimensions or access roads.

Prepare Information for a Project Quote

A useful quotation package includes the one-line diagram, system voltage and frequency, source details, load schedule, fault-current information, grounding method, and required switching sequence. Add enclosure location and environmental conditions, preliminary equipment arrangement, feeder quantities, metering needs, control requirements, and applicable specifications. Mark unresolved items clearly so assumptions can be reviewed before design proceeds.

Also share project schedule, shipping destination, delivery restrictions, drawing and submittal expectations, and the parties responsible for studies, controls, and field installation. A U.S. manufacturer can build new equipment with American components, provide custom fabrication, and ship nationwide; lead time depends on confirmed scope and project conditions. Final configuration requires engineering review and AHJ coordination.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields