Request a Quote

Built for your application

Pipeline Pump Station Power

Pipeline pump stations need power systems coordinated with motor duty, control philosophy, site conditions, and outage response. We build new switchgear and distribution equipment to project requirements for Ohio and nationwide delivery.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Three gray switchgear cabinets on wooden pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start with the Pumping Duty

A station’s electrical arrangement begins with the pumping profile: number and size of pumps, operating combinations, expected starts per hour, and whether flow must continue during maintenance. These inputs shape feeder capacity, bus arrangements, motor-starting choices, and the extent of standby power required.

Identify the utility service, voltage, available fault current, and anticipated expansion before selecting equipment. Gather motor nameplate data, pump operating sequences, site one-line diagrams, and load studies when available. The responsible engineer should reconcile these details with utility requirements and the authority having jurisdiction (AHJ).

Coordinate Motor Feeders

Each motor feeder must suit the motor’s voltage, full-load current, starting characteristics, conductor arrangement, and protection requirements. Review overload protection, short-circuit protection, disconnecting means, and coordination with upstream devices as a system; a feeder choice should not be based on horsepower alone.

For multiple pumps, determine whether feeders share a lineup or require separated sections, and how bus capacity changes when units run concurrently. Confirm incoming and outgoing cable entry, termination space, metering, and future feeder provisions. These layout decisions affect the switchgear or switchboard arrangement and installation planning.

Choose a Starting Method Deliberately

Across-the-line starting is straightforward, but its inrush and voltage dip may challenge a weak source or disturb nearby loads. Reduced-voltage starters, soft starters, or variable-frequency drives can address particular operating and process needs, yet introduce added equipment, heat, harmonics, bypass questions, or maintenance considerations.

The engineer should compare the motor manufacturer’s requirements, pump torque curve, acceleration time, starts per hour, and utility limits. Confirm whether speed control is needed, whether a bypass is required, and how the selected starter interfaces with feeder protection. No starting method is universally best for every station.

Define Local and Remote Control

Control architecture should specify what operators can do at the equipment, station panel, and supervisory control system. Document start permissives, stop commands, local/remote selection, alarm points, and the response to loss of communications. Remote commands should not bypass required protective functions or safe operating procedures.

Confirm signal types, control power, interface ownership, and communications protocol with the controls integrator and station operator. Specify whether the power equipment needs control wiring compartments, terminal blocks, status indication, or provisions for future points. The quote package should distinguish supplied equipment from field devices and integration work.

Plan Standby Power Around Critical Loads

Standby requirements depend on the consequence of losing pumping, allowable interruption, and the loads that must remain energized. Identify whether backup power is intended for selected pumps, controls, instrumentation, lighting, or all station loads; a generator sized only from running kilowatts may not handle motor starting.

Coordinate generator capacity and transient response with the largest starting event, other connected loads, and any load-shedding sequence. Confirm transfer arrangement, source interlocking, grounding method, and whether standby operation is automatic or operator initiated. The responsible engineer and utility should review the proposed source transition and protection scheme.

Account for Protection and Operating Conditions

Protection settings depend on source characteristics, motor data, conductor limits, and coordination objectives. Review ground-fault protection where applicable, arc-flash study inputs, relay or trip-unit functions, and selective coordination requirements. Final settings and labels are project-specific engineering work, not assumptions that can be made from an equipment description.

Pipeline stations may have temperature extremes, dust, moisture, vibration, corrosive exposure, or classified locations. Confirm enclosure construction, environmental ratings, space conditioning, and applicable hazardous-area boundaries with the project team. The equipment specification should identify site conditions and governing codes rather than assume a standard indoor electrical room.

Select the Equipment Architecture

UL 891 switchboards and UL 1558 low-voltage switchgear are distinct equipment categories; the project specification and design determine the appropriate construction. Medium-voltage service or motor loads require equipment designed for that voltage class, not a low-voltage UL 891 switchboard. Confirm service voltage and the utility’s metering and protection requirements first.

A lineup may include service entrance sections, distribution breakers, motor-feeder provisions, metering, and control compartments, depending on scope. Custom fabrication can address project-specific arrangements and interfaces. We build new equipment in the United States with American components; applicable construction and listing details must be confirmed for each configuration.

Prepare a Complete Quote Package

For a useful quotation, provide the one-line diagram, service data, motor schedule, feeder requirements, starter preferences, control narrative, standby-power concept, and available fault-current information. Include drawings, specifications, applicable codes, site conditions, delivery constraints, and the requested scope boundary for equipment, accessories, and documentation.

Identify required submittals, factory options, cable entry, shipping splits, and coordination deadlines. We supply newly manufactured switchgear and power distribution equipment with custom fabrication, short lead times, and nationwide shipping; schedule and configuration depend on the project. Have the responsible engineer, utility, and AHJ review applicable design decisions.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields