Request a Quote

Ratings & specifications

Zone-Selective Interlocking

Zone-selective interlocking coordinates compatible protective devices so an upstream breaker can respond differently when a downstream device signals a fault. Review its communications path, settings, and application limits before specifying equipment.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Rows of gray electrical distribution cabinets on pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

What the interlocking signal changes

Zone-selective interlocking, often abbreviated ZSI, is a coordination method in which compatible trip units exchange a restraint or blocking signal. When a downstream device detects a fault within its zone, it signals an upstream device to delay its response according to the engineered coordination scheme. Without that signal, the upstream device may respond more quickly to limit fault duration.

ZSI does not replace overcurrent protection, establish system ratings, or guarantee selectivity for every fault. Its behavior depends on device compatibility, wiring, programmed functions, and settings. The responsible engineer must evaluate the intended response across applicable fault levels and operating configurations, including any conditions where the interlocking signal is absent or invalid.

Map devices and protection zones

Start with a one-line diagram that identifies each protective device, its location, and the loads or feeder sections it protects. The engineer can then define which downstream devices should signal which upstream devices. A main breaker may receive signals from feeder breakers, while additional tiers require deliberate assignment of signal paths and device roles.

Do not assume that every breaker in a lineup participates in one common ZSI zone. The selected trip units and communications terminals must support the intended arrangement, and each device’s function must be clear. For a quote, provide the proposed lineup, device schedule, system voltage, and a marked diagram showing the desired upstream-downstream relationships.

Confirm device and trip-unit compatibility

Interdevice signaling is manufacturer- and device-specific. Confirm compatibility among breaker frames, electronic trip units, firmware or accessory requirements where applicable, and the specific ZSI functions required. A breaker that provides ordinary overcurrent protection may not support the intended interlocking interface, or may support only selected protection elements.

Compatibility should be checked for the complete signal chain, not just one upstream and one downstream breaker. Identify the exact device catalog information or proposed trip-unit features for each position. If equipment is being specified before device selection, state the design intent and allow the manufacturer and engineer to resolve compatible configurations before drawings and settings are finalized.

Plan the signal path and wiring

The design must define how the restraint signal travels between devices, including terminal assignments, conductor routing, polarity or connection conventions where applicable, and separation from other circuits as required by the selected equipment. The chosen interconnection method must suit the switchboard or switchgear arrangement and preserve the intended relationship between adjacent protection zones.

Long runs, lineup boundaries, remote equipment, and field-installed connections deserve particular review. Confirm who supplies and installs interconnecting conductors, how terminations will be identified, and what drawings or wiring schedules are needed. Quote documents should show equipment locations and the intended interfaces; final wiring details must follow the selected device documentation and project-approved design.

Coordinate settings with system studies

ZSI settings must be considered alongside pickup values, time delays, instantaneous functions, ground-fault protection where specified, and the system’s available fault current. A coordination study should assess whether the intended devices detect and signal for relevant faults, and whether the resulting responses meet the project’s coordination objectives without exceeding equipment limitations.

Study inputs commonly include utility source information, transformer data, conductor impedances and lengths, motor contributions where applicable, protective-device data, and normal and alternate operating modes. Provide the latest available information and identify assumptions. The responsible engineer should determine settings and verify the design; equipment suppliers should not infer final settings from a brief device list.

Account for operating modes and boundaries

A scheme that works in one normal configuration may behave differently when a tie breaker closes, a source changes, or loads transfer between buses. Map each permitted operating mode and identify whether ZSI signals cross the relevant boundary. Where a signal path does not exist, protection behavior must be evaluated on its own rather than presumed to match the normal arrangement.

Also define what should happen during maintenance, commissioning, or a device replacement that interrupts the interlocking circuit. Any bypass, test method, alarm, or fallback response is a project-specific design decision, not an assumed feature. The engineer should document how operators recognize the active configuration and how changes are controlled and verified.

Specify equipment and documentation needs

For newly manufactured equipment, identify the applicable equipment type and standard separately from the ZSI function. UL 891 applies to low-voltage switchboards; UL 1558 applies to low-voltage switchgear. Neither designation makes medium-voltage equipment covered by those standards. Confirm the required assembly type, interrupting and withstand considerations, and device arrangement for the application.

A useful request for quotation includes the one-line diagram, device schedule, ZSI zone map, available system data, preferred equipment construction, and scope split for field wiring. State whether settings are preliminary or engineer-approved and list required submittals. Custom fabrication can address project-specific layouts, while lead time and nationwide shipping depend on the finalized configuration and scope.

Review, build, and verify the scheme

Before release, review approved drawings for device identification, signal connections, terminal references, and alignment with the coordination study. Establish responsibility for setting entry, point-to-point wiring checks, and functional verification. Any test procedure should use the selected device manufacturers’ instructions and the project’s safety and commissioning requirements.

Our U.S.-built equipment uses American components and can be custom fabricated for project requirements, subject to confirmed design and component availability. The responsible engineer, utility, and authority having jurisdiction should review applicable design matters. Provide revisions promptly, since changes to breaker selection, bus arrangement, or operating modes can affect both ZSI coordination and the equipment quotation.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields