Request a Quote

Ratings & specifications

Circuit Breaker Interrupting Rating

A circuit breaker’s interrupting rating must be adequate for the fault current available at its line terminals under the applicable system conditions. Sound selection starts with a documented fault study, not a breaker label considered in isolation.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Three gray switchgear cabinets on wooden pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

What the interrupting rating means

The interrupting rating is the maximum prospective short-circuit current a circuit breaker is rated to interrupt under specified conditions. It is not the normal load current rating, and it does not indicate how much current the breaker can carry continuously. Both values matter, but they answer different design questions.

For selection, compare the breaker’s applicable interrupting rating with the available fault current at its line-side terminals. The comparison must use compatible voltage and rating bases. A rating stated for one voltage or tested arrangement should not be assumed valid for every application; confirm the manufacturer’s documentation for the specific breaker.

Establish fault duty at the installation point

Prospective fault current is the current that could flow at a point in the system if a fault occurred, before the protective device interrupts it. The value depends on the utility source, transformer impedance and rating, conductor lengths and sizes, and the network configuration. It can vary substantially between service equipment and downstream panels.

Use a short-circuit study or other engineering analysis appropriate to the project, with source data and assumptions documented. For utility-connected systems, obtain available fault-current information from the utility when needed. Confirm the study reflects the intended operating configuration, including parallel sources, ties, generators, and other sources that can feed a fault.

Check voltage, poles, and rating basis

A breaker’s interrupting capability is tied to its listed or otherwise documented conditions, including system voltage and pole arrangement. Verify the actual circuit voltage, grounding method, and number of poles against the breaker’s markings and technical information. Do not carry a rating from a different voltage or device configuration into the design without confirmation.

Also distinguish an individual breaker interrupting rating from an assembly short-circuit rating or withstand rating. A switchboard or switchgear assembly includes bus, supports, connections, and protective devices whose limits must be coordinated. The complete equipment configuration and its applicable documentation must suit the calculated duty at the installation point.

Account for system configuration and sources

Fault duty is not always a single fixed number. Utility operating changes, transformer replacements, closed tie breakers, parallel transformers, and onsite generation can raise the current available to a device. Conversely, an open tie or a different source arrangement may produce a lower value. The design basis should identify the configurations that can occur during normal operation.

Where multiple operating states are credible, have the responsible engineer evaluate each relevant case and identify the highest applicable duty at the breaker. Include generators, motors, energy storage, and other sources as required by the study method. A selection based only on the normal utility-fed state may miss a more demanding configuration.

Understand series-rated combinations carefully

A series rating may permit a specific upstream protective device to limit the fault current seen by a downstream breaker, but it is not a general substitute for matching each breaker’s standalone interrupting rating to available fault current. The combination must be specifically documented for the devices, ratings, and conditions used.

Confirm the exact upstream and downstream catalog identifiers, equipment arrangement, voltage, and applicable labeling or documentation with the manufacturer and design team. Changes to either protective device can invalidate the intended combination. The engineer should verify that the proposed approach is permitted for the installation and acceptable to the authority having jurisdiction.

Coordinate ratings within the equipment assembly

A breaker can have an adequate interrupting rating while another component in the assembly remains a limiting factor. Bus bracing, incoming devices, feeder devices, and the assembly’s documented short-circuit rating all require review. The equipment rating must be appropriate for the available fault current and the specific construction being supplied.

For new switchboard or switchgear requirements, identify the system voltage, service or feeder location, calculated fault duty, and desired main and branch arrangement. UL 891 switchboards and UL 1558 low-voltage switchgear are distinct equipment categories; neither designation alone establishes that a particular configuration meets project fault-duty requirements.

Provide complete information for equipment selection

A useful request for quotation includes the one-line diagram, available fault-current values and study basis, nominal voltage, phase and wire configuration, grounding method, and source details. Identify transformer nameplate data, utility contribution if available, conductor information, and any generator or tie arrangements that affect fault current.

Also state the equipment type, main and feeder device requirements, installation location, and any specified standards or project documents. If study data are preliminary, mark them as such rather than presenting estimates as final. The manufacturer can review the requested configuration and identify information that needs clarification before equipment selection is finalized.

Review the design before release

Before release, reconcile the breaker documentation, equipment configuration, and latest fault study. Recheck when a utility changes source data, a transformer or conductor is revised, or the one-line diagram changes. Keep the basis of design and device identification aligned so field personnel can verify that installed equipment matches the approved design.

The responsible engineer should confirm fault-duty adequacy and coordination, while the utility and AHJ should be consulted where their requirements apply. A U.S. manufacturer can custom-fabricate new distribution equipment and ship nationwide, but project-specific ratings, approvals, and configuration must be confirmed rather than presumed.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields