Request a Quote

Ratings & specifications

Harmonic Load Considerations

Nonlinear equipment can reshape current waveforms, increase neutral loading, and affect measurement and thermal decisions. Review load data, system configuration, and metering needs before specifying new distribution equipment.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Switchgear cabinets in an electrical equipment room
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start With the Loads That Produce Harmonics

Harmonic currents arise when loads draw current in pulses rather than in a smooth waveform. Common examples include variable-frequency drives, UPS systems, rectifiers, LED drivers, and electronic power supplies. Their presence alone does not define the required switchboard design; quantity, operating profile, phase distribution, and connection details matter.

For a new equipment specification, identify each significant nonlinear load by type, quantity, input rating, and expected operating schedule. Obtain manufacturer data when available, including harmonic current information or a load study. Distinguish loads that run together from standby or intermittent equipment, and note planned future additions.

Understand Harmonic Current and Neutral Loading

In a three-phase, four-wire system, certain triplen harmonics—especially the third harmonic and its multiples—can add in the neutral instead of canceling as fundamental-frequency phase currents often do. A neutral sized only from balanced phase-load assumptions may therefore be inadequate where substantial nonlinear single-phase loads are present.

The responsible engineer should evaluate the expected neutral current under credible operating conditions, considering phase imbalance and the harmonic spectrum. Confirm conductor and bus requirements, neutral connections, and any applicable code provisions for the specific design. Do not infer a neutral rating from total load alone or assume all electronic loads behave alike.

Coordinate System Configuration and Bus Design

System voltage, phase count, wire count, grounding arrangement, and available fault current shape the equipment design independently of harmonic concerns. A distribution assembly may need a full-capacity neutral, particular bus arrangements, or space for feeder distribution, but these are project decisions that depend on calculated loading and the selected equipment type.

Provide the one-line diagram and identify source and load connections, transformer details, feeder destinations, and anticipated demand. The design team can use these inputs to coordinate bus ratings, neutral provisions, protective devices, and enclosure layout. Confirm applicable requirements with the responsible engineer and authority having jurisdiction before releasing a specification.

Treat Thermal Effects as a Design Input

Harmonic currents can increase heating in conductors and equipment through higher RMS current and frequency-dependent effects. Actual temperature rise depends on the spectrum, current magnitude, equipment construction, ventilation, ambient conditions, and loading duration. A harmonic label or a single distortion percentage is not enough to establish the thermal needs of an assembly.

Share available measurements or engineering calculations, including load profiles and harmonic orders, rather than relying on an assumed derating factor. Review the proposed configuration for bus and neutral loading, conductor terminations, and enclosure conditions. Any required temperature limits, environmental conditions, or operating margins should be specified and verified for the project.

Specify Metering That Answers the Right Questions

Basic voltage, current, power, and energy readings may not reveal the harmonic behavior behind an operating issue. If monitoring is part of the project, define whether the goal is operational trending, power-quality investigation, billing support, or troubleshooting. These purposes can call for different measurement points, data intervals, communications, and instrument capabilities.

Confirm whether meters should report total harmonic distortion, individual harmonic components, neutral current, demand, or event data. Identify required accuracy, display needs, network protocol, integration destination, and whether current transformers or other sensors are required. Meter functions vary by device, so specify the measurements rather than assuming every meter includes them.

Coordinate Protection and Power-Quality Measures

Protective-device selection should reflect the actual load and system study, not simply the presence of nonlinear equipment. Review continuous loading, inrush, coordination objectives, interrupting requirements, and the effects of any upstream or downstream mitigation. Harmonic filters, line reactors, or other measures may be considered by the engineering team, but are not automatic switchboard features.

If mitigation is proposed, establish its location, ratings, control approach, and compatibility with the source and loads before equipment layout is finalized. Confirm whether the assembly must accommodate associated components or connections. Filter performance and system interactions require application-specific analysis; coordinate the design with the responsible engineer and utility when their review is relevant.

Choose Equipment Within Its Applicable Standard

For low-voltage distribution, distinguish a UL 891 switchboard from UL 1558 low-voltage switchgear when defining the equipment. They are different equipment categories, and the selection should follow system requirements, application, and project specifications. Neither designation should be treated as a substitute for evaluating the harmonic loading or neutral design.

Medium-voltage equipment is a separate design category and is not covered by UL 891. Provide operating voltage, system arrangement, source information, and applicable project criteria so the manufacturer can determine the appropriate scope. Required construction, ratings, and documentation must be confirmed for the specific build; do not assume approvals or features without written confirmation.

Prepare Complete Information for a New Equipment Quote

A useful quote package includes the one-line diagram, voltage and frequency, phase and wire arrangement, source and fault-current data, load schedule, nonlinear-load inventory, and known harmonic measurements or studies. Include neutral-current expectations, metering functions, protection requirements, environmental conditions, installation constraints, and requested equipment standard or construction category.

Flag uncertainties, future capacity needs, delivery milestones, and interfaces with existing systems, while making clear which details remain subject to engineering review. A U.S. manufacturer building with American components can review custom-fabrication requirements and nationwide shipping needs for new equipment. Final design should be checked by the responsible engineer, utility, and AHJ where applicable.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields