Count Circuits by Function and Load
Start with the circuits the lineup must serve, not a preferred number of breaker spaces. List each load or downstream distribution panel, its voltage, phase, estimated demand, and operating role. Separate normal, standby, and process loads where applicable; their distinct operating conditions may affect feeder ratings and protective-device coordination.
Use the project load study and one-line diagram to establish the feeder schedule. A feeder count based only on connected equipment can miss shared loads, future additions, or circuits that need individual isolation. Have the responsible engineer verify demand, diversity assumptions, and the intended system arrangement before equipment configuration begins.
Specify Each Feeder’s Electrical Duty
A circuit count does not define the equipment. For every feeder, identify its required continuous current, voltage, number of poles, and expected load characteristics. Motor starting, transformer energization, nonlinear loads, and other operating conditions can influence the selected protective device and its settings, subject to the approved design.
Also provide available fault current at the lineup and the protection requirements established by the engineer. Short-circuit ratings, interrupting ratings, and coordination are design checks, not values to infer from feeder quantity. Confirm the applicable equipment standard and project specifications; UL 891 switchboards and UL 1558 low-voltage switchgear are distinct product categories.
Choose Breaker and Feeder Arrangements
Feeder devices may differ in frame size, trip unit, pole count, and mounting arrangement. A lineup serving a few large loads may require a different section layout from one with numerous smaller circuits, even when their aggregate current is similar. Indicate which circuits require dedicated devices and identify any specified control or indication functions.
The selected arrangement depends on equipment type, ratings, and the manufacturer’s buildable configuration. Do not assume every breaker size or feature fits every section or is interchangeable. Submit the one-line, feeder schedule, control requirements, and applicable specifications so the proposed new lineup can be reviewed against the project design.
Resolve Cable Termination Requirements
For each feeder, provide conductor material, quantity per phase, size or range, insulation, and whether conductors enter from above or below. Identify lug requirements, cable routing constraints, and whether the installation uses conduit, cable tray, or another approved method. These details determine termination space and help avoid clashes with adjacent devices or barriers.
Confirm the project’s minimum bending space, pulling access, and working clearances with the responsible electrical designer and installation contractor. Cable sizes and lug arrangements must suit the actual feeder rating and installation conditions. If conductors are unusually large or numerous, flag them early; the section layout may need adjustment before fabrication.
Plan Section Width, Depth, and Access
Feeder quantity influences lineup dimensions, but it does not translate directly into a fixed number of circuits per section. Device dimensions, bus arrangement, cable compartments, barriers, and termination access all affect usable space. The specified enclosure and site conditions also matter, including indoor or outdoor placement and available room for equipment access.
Provide room dimensions, entrance direction, adjacent equipment locations, and any restrictions on lifting, doors, or service access. Confirm the intended lineup arrangement and cable-entry plan against the project drawings. Custom fabrication can address project-specific layouts, but feasibility and dimensions must be reviewed for the selected equipment and required ratings.
Decide What Spare Ways Mean
A spare way can mean an installed protective device, an equipped but unused position, or reserved physical space for a later addition. These options are not equivalent. State which circuits are required initially and whether future capacity means a complete feeder, a provision for a device, or room for another section.
For each planned spare, identify anticipated voltage, current, pole count, and likely cable route if known. Verify that bus capacity, enclosure layout, and the project’s short-circuit requirements accommodate the intended future use. Unassigned spaces should not be assumed to include a breaker, lugs, or other components unless the quote defines them.
Check Coordination and System Boundaries
Review feeder devices in the context of upstream protection, downstream equipment, grounding, and the available fault current. The engineer should confirm protective-device selections and coordination objectives for the complete system. Where selective coordination or emergency-system rules apply, document the applicable requirements rather than relying on generic feeder descriptions.
Identify whether the lineup is a switchboard, low-voltage switchgear, or part of a medium-voltage system; these categories have different construction and applicable standards. UL 891 applies to switchboards, while UL 1558 applies to low-voltage switchgear. Medium-voltage equipment requires its own appropriate design basis and is not covered by UL 891.
Prepare a Quote-Ready Feeder Schedule
A useful request includes the one-line diagram, feeder schedule, system voltage, service or distribution role, available fault current, and required equipment standard. For each circuit, list load description, rating, poles, protective-device requirements, cable details, termination direction, and any metering or control needs. Mark required feeders separately from future provisions.
Include enclosure conditions, room and access constraints, project specifications, and the desired shipment destination. A U.S. manufacturer building with American components can review a custom configuration and arrange nationwide shipping; lead time depends on the defined scope and component availability. The responsible engineer, utility, and AHJ should review applicable design and installation requirements.