Request a Quote

Ratings & specifications

Current Transformer Selection

Select current transformers by matching the primary current, connected burden, accuracy requirements, and physical arrangement to the intended metering or protection function. Clear project information helps coordinate CTs with newly manufactured distribution equipment.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Three gray switchgear cabinets on wooden pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start With the CT’s Intended Function

A current transformer (CT) scales primary current to a lower secondary value for a meter, relay, or monitoring device. First identify what the CT must do: revenue or operational metering, overcurrent protection, ground-fault sensing, or another defined function. One installation may need separate CTs for measurement and protection.

The application determines which characteristics matter most. Metering CTs are evaluated for accuracy across expected operating currents and connected instruments; protection CTs must support the relay’s needs during fault conditions. Confirm the device model, input rating, wiring arrangement, and project criteria rather than assuming one CT can serve every purpose.

Choose a Ratio From Expected Current

CT ratio expresses the relationship between primary and secondary current, such as a primary rating paired with a standard secondary output. Select a ratio that accommodates the equipment’s rated current and expected operating range while providing useful resolution for the meter or relay. A ratio chosen only from nominal load may not suit future operating conditions.

Provide the system voltage and frequency, equipment continuous-current rating, expected load range, and any planned capacity changes. Confirm the connected device’s required secondary input and whether the design uses a one-ampere or five-ampere secondary. The responsible engineer should verify ratio selection against load calculations, protection settings, and applicable utility requirements.

Calculate the Connected Burden

Burden is the load imposed on a CT secondary circuit, commonly considered as impedance or volt-amperes at a specified power factor. Include the meter or relay input, test switches, terminal blocks, and lead-wire resistance. Long secondary runs can add meaningful burden, especially when conductors are undersized or the circuit uses a five-ampere output.

Compare the calculated burden with the CT’s specified capability at the required accuracy. Do not treat a catalog burden value as proof that the complete installed circuit will meet its measurement or protection objective. For a quote, identify approximate lead length, conductor size if established, connected devices, and the intended secondary-circuit arrangement.

Define Accuracy for the Application

Accuracy requirements depend on what decisions rely on the current signal. Utility revenue metering may be subject to utility rules and specified accuracy classes, while facility monitoring may have different measurement objectives. Protection applications instead require suitable performance under fault-current conditions; the relevant class or characteristic must match the relay scheme and coordination study.

Identify the governing specification, required accuracy class, current range of interest, and any utility or owner criteria. For protection, provide the relay type and the design information needed to assess CT response, including anticipated fault levels where available. The engineer of record and utility should resolve conflicting requirements before a CT configuration is finalized.

Check Physical Fit and Mounting

Electrical performance does not establish that a CT will fit. Confirm conductor or bus dimensions, insulation clearances, mounting method, available space, and access for installation and maintenance. Window, bar, and other CT constructions have different interface needs; the appropriate form depends on the equipment layout and the conductor path.

For equipment integration, share enclosure and compartment constraints, bus arrangement, phase spacing, cable entry direction, and relevant drawings. Identify whether the CT must be installed around an existing conductor during assembly or connected to a specified bus configuration. Final clearances and mechanical support must be reviewed against the equipment design and applicable requirements.

Coordinate Secondary Wiring and Polarity

CT secondary wiring must match the intended metering or protection diagram. Confirm terminal identification, polarity, grounding approach, shorting provisions, and the destination of each secondary circuit. Incorrect polarity or an unsuitable circuit arrangement can affect directional elements, differential protection, and measurement interpretation, so these details belong in the engineered design.

CT secondaries require careful handling because an energized primary with an open secondary can create hazardous voltage. Specify the intended shorting terminal blocks or test facilities where required by the design, and document circuit labels and termination points. Installation, commissioning, and maintenance procedures should be established by qualified personnel under applicable safety practices.

Coordinate CTs With Equipment Standards

CT integration depends on the equipment type and its construction. In low-voltage assemblies, distinguish a UL 891 switchboard from UL 1558 low-voltage switchgear; the applicable product standard and project specification affect the assembly context, not a blanket CT selection. Medium-voltage equipment has different insulation and application considerations and is not covered by UL 891.

Confirm CT locations, compartment arrangement, instrument connections, and the required equipment standard with the project drawings and specification. The manufacturer can review the proposed interface for a new equipment build, but the responsible engineer must validate the protection and measurement design. Utility and authority having jurisdiction (AHJ) review may also apply.

Prepare a Complete Quote Request

A useful request identifies equipment type, system voltage, frequency, rated current, CT function, ratio, secondary rating, accuracy criteria, burden information, and physical dimensions. Include one-line diagrams, elementary or wiring diagrams, bus and enclosure details, device data, and applicable project or utility specifications when available.

Also note quantities, required delivery location, project schedule, and any drawing-submittal needs. The manufacturer builds new switchgear and power distribution equipment in the United States using American components, offers custom fabrication, and ships nationwide. Final CT selection and assembly configuration remain subject to design review and confirmation of project requirements.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields