Request a Quote

Ratings & specifications

Clearance and Creepage Specifications

Clearance and creepage are related but distinct insulation dimensions: one crosses air, the other follows a surface. Their design depends on equipment class, voltage, environment, geometry, and applicable standards.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Electrical distribution lineups in a spacious equipment facility
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Two Paths, Different Insulation Concerns

Clearance is the shortest distance through air between conductive parts at different electrical potentials. Creepage is the shortest path along an insulating surface between those parts. Both help manage insulation performance, but they address different physical conditions and cannot be treated as interchangeable dimensions on a drawing.

A bus-to-bus air gap may govern clearance, while the path across a support, barrier, or molded component may govern creepage. The controlling point is not always visually obvious, especially around fasteners, bends, edges, and enclosure partitions. Review the actual assembled geometry, not just nominal spacing in a layout.

Start With Equipment Class and Standard

Applicable requirements depend on what the equipment is and how it is evaluated. UL 891 applies to low-voltage switchboards; UL 1558 addresses low-voltage switchgear. Medium-voltage equipment is a separate category with its own applicable standards and insulation coordination considerations. UL 891 should not be presented as a medium- or high-voltage standard.

The responsible engineer should identify the product category, system voltage, intended use, and governing code or standard basis before setting dimensions. Requirements can vary with construction, component type, and evaluation route. Confirm project expectations with the manufacturer and, where relevant, the utility and authority having jurisdiction.

Voltage Is Necessary, but Not the Whole Basis

Operating voltage is an important input, but it does not alone establish acceptable spacing. Engineers may need to account for the voltage between adjacent conductors, phase-to-ground conditions, transient overvoltages, insulation level, and the way the equipment is applied. The relevant working and impulse conditions depend on the design and applicable standard.

Provide nominal system voltage, grounding arrangement, frequency, and any specified withstand or insulation coordination criteria when requesting a design review or quote. Identify whether the assembly includes multiple voltage sections or control circuits with separate potentials. The responsible engineer should verify the assumptions against the one-line diagram and project requirements.

Environment Changes the Surface-Path Question

Creepage is particularly sensitive to the insulating surface and its surroundings. Dust, condensation, conductive deposits, humidity, and industrial contamination can affect surface behavior and maintenance needs. Indoor installation does not by itself establish a clean, dry environment; process areas, washdown zones, and unconditioned spaces may present different conditions.

Describe the installation location, enclosure conditions, expected contaminants, altitude if relevant to the design basis, and cleaning or maintenance practices. Also note outdoor exposure or unusual temperature and moisture cycles. These details help the design team determine which environmental assumptions apply rather than relying on an unverified generic spacing value.

Geometry, Materials, and Assembly Tolerances

The shortest path can change with component shape. Sharp projections, slots, punched openings, bus supports, barrier edges, and conductor movement may create a tighter air gap or surface route than a straight-line measurement suggests. Fabrication tolerances and installation access also matter because intended spacing must remain meaningful in the finished assembly.

Specify bus material and arrangement, conductor sizes, insulating supports, barriers, and any required cable entry or termination locations. For custom fabrication, drawings should show critical dimensions and interfaces clearly. The manufacturer can review buildable geometry, while the responsible engineer retains responsibility for design criteria and field coordination.

Switchboard and Switchgear Configuration Details

A distribution assembly may combine incoming equipment, bus compartments, feeder devices, metering, and control wiring. Each arrangement can create distinct potential differences and insulation paths. Drawout construction, barriers, cable compartments, or closely coordinated sections may affect where clearances and creepage paths need evaluation.

For a quote, provide the one-line diagram, preliminary elevation, device schedule, bus ratings, section arrangement, and control-voltage information when available. Flag future extensions, unusual feeder terminations, and space constraints. These are project-specific inputs, not features assumed to be included in every manufactured assembly.

Medium-Voltage Applications Need Their Own Review

Medium-voltage designs require insulation coordination appropriate to their voltage class and application. Air spacing, insulating surfaces, field distribution, impulse withstand, terminations, and enclosure configuration must be considered together. A low-voltage dimensional rule or switchboard convention should not be carried over without a valid engineering basis.

Identify system voltage, grounding method, utility requirements, switching arrangement, cable type, and specified withstand levels for medium-voltage requests. The responsible engineer should coordinate the insulation basis with the utility and applicable project standards. Confirm the intended equipment classification and evaluation requirements before comparing proposed dimensions.

Information That Supports a Sound Specification

A useful specification states the governing standard and edition where known, equipment class, system conditions, environmental assumptions, and any project-specific insulation criteria. Include drawings, interface dimensions, conductor arrangement, and anticipated accessories. If a value is preliminary or owner-specified, label it clearly so it is not mistaken for a verified design requirement.

The U.S. manufacturer builds new switchgear and power distribution equipment with American components, offers custom fabrication, and ships nationwide. For an Ohio or other U.S. project, submit the available electrical and installation data for review. The responsible engineer, manufacturer, utility, and AHJ should resolve applicable requirements before release.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields