Request a Quote

Ratings & specifications

Switchgear Bus Configuration

Bus configuration shapes how sources feed loads, how operators manage outages, and how equipment is arranged. Compare common layouts alongside protection, coordination, space, and project-specific requirements.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Motor control center lineup inside an industrial building
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start with the operating objective

A bus arrangement is a system-level decision, not simply a choice of lineup sections. Define which sources must serve which loads, whether loads can tolerate an interruption during transfer, and what portions of the system need to remain available during maintenance or a fault.

Document normal and alternate operating states before selecting equipment. Identify the utility service, generators, transformers, major load groups, and any planned load shedding. The responsible engineer should verify that the proposed arrangement matches the one-line diagram, protection philosophy, operating procedures, and applicable project requirements.

Single-bus layouts: simplicity and limits

A single bus connects incoming sources and outgoing feeders to one common bus. This arrangement can be straightforward to lay out and operate, but a bus fault or maintenance affecting the common section may interrupt multiple loads. The actual interruption scope depends on sectionalizing and protection design.

Consider single-bus service when the project can accept its outage implications and the source arrangement is uncomplicated. Confirm incoming device locations, feeder distribution, fault-duty requirements, and any future expansion plans. Adding capacity later may require shutdowns or substantial lineup changes, so reserve needs should be addressed early.

Sectionalized buses and tie breakers

A sectionalized bus divides the bus into portions, commonly connected through a tie breaker or other specified switching device. With suitable source and feeder connections, sections may be operated separately or connected. This can limit the loads affected by certain events, but does not guarantee continuity.

Specify normal tie position and the permitted switching sequence. Confirm whether operators may close the tie with both sources energized, and whether interlocking, synchronization checks, or transfer controls are required. Protection settings and coordination must account for each approved configuration, including changes in available fault current.

Two sources, transfer, and paralleling

Two incoming sources may feed separate bus sections, with a tie used to transfer selected loads when one source is unavailable. A break-before-make scheme avoids intentional source paralleling, while closed-transition transfer briefly connects sources and requires engineering review of their compatibility and control requirements.

For utility-generator or transformer-generator combinations, confirm source voltage, grounding, phase relationships, available fault current, and operating restrictions. Identify whether automatic transfer is required, which loads transfer, and what prevents unintended paralleling. The utility, generator controls engineer, and authority having jurisdiction may need to review the design.

Main-tie-main arrangements

Main-tie-main describes two main devices serving separate bus sections and a tie device between them. The arrangement can support alternate feeding, but its operating logic depends on source availability, interlocks, transfer controls, and whether the tie is normally open or closed.

For a quote, provide the intended switching sequence and state whether transfer is manual or automatic. Clarify whether both mains may operate together, how overloads or source loss are handled, and which loads have priority. Device selection and bus ratings must be based on documented system conditions, not the arrangement name alone.

Double-bus and specialized arrangements

Double-bus arrangements provide more than one bus path, but the switching devices and connections needed to select or transfer between paths add complexity. They are not interchangeable with a sectionalized single bus. Evaluate whether the added operating flexibility addresses a specific maintenance or availability objective.

Other configurations may be appropriate for specialized facilities, but their feasibility depends on equipment type, voltage class, protection scheme, and operating practice. Describe the required functions rather than requesting a topology by name alone. The design team should establish how each device position affects isolation, metering, and load continuity.

Segregation, barriers, and equipment class

Segregation describes how functional compartments or components are separated within an assembly; it does not by itself establish an interruption rating or eliminate exposure to electrical hazards. Confirm the applicable construction standard, internal separation expectations, access needs, and whether cable or bus compartments require specific barriers.

UL 891 applies to low-voltage switchboards, whereas UL 1558 covers low-voltage switchgear. Medium-voltage equipment is a separate equipment class with different applicable standards and design constraints. Specify the intended class and project requirements; do not assume a bus arrangement determines the assembly’s listing or construction.

Information for configuration and quotation

A useful quotation package includes a current one-line diagram, system voltage and frequency, source details, load schedule, available fault current, grounding method, and required ratings. Also provide lineup location, incoming and outgoing cable or bus connections, access direction, dimensions, metering, controls, and any site or utility constraints.

State the preferred bus arrangement, normal operating state, transfer intent, segregation expectations, and planned expansion. Identify standards, approvals, and documentation required for the specific build, then have the responsible engineer review the design with the utility and AHJ where relevant. U.S.-built equipment, custom fabrication, short lead times, and nationwide shipping can support projects in Ohio and across the country.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields