Request a Quote

Power distribution equipment

Plug-In Busway

New plug-in busway can distribute power along production lines and facility spaces, but tap-off placement, compatible units, access clearances and downstream protection must be coordinated with the electrical design.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Installed switchboard lineup beneath overhead conduit
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Plan the route around loads and change

Plug-in busway uses a continuous distribution run with designated openings for compatible tap-off units. It can suit facilities where loads are spread along a production line, warehouse aisle or service area, particularly when equipment locations may change. The route and tap-off plan should begin with the actual loads and operating layout, not simply the shortest path between electrical rooms.

Map current equipment, anticipated additions, operating schedules and any areas where future connections may be needed. Identify which loads require dedicated circuits, which operate together, and where maintenance or production changes could affect access. A preliminary load schedule helps the responsible engineer assess feeder capacity, distribution arrangement and practical tap-off locations before equipment is specified.

Set tap-off points for safe, useful access

A tap-off location must work electrically and physically. Consider the position of each load connection, cable or conduit routing, nearby machinery, doors, storage zones and routine traffic. A location that is convenient on a drawing may be obstructed by a lift, material rack or process equipment once the space is operating.

Confirm the manufacturer’s permitted tap-off positions and spacing for the selected busway design. Required arrangements can vary by system, enclosure, orientation and tap-off type; do not assume every opening accepts every unit. Provide a marked route plan showing proposed connection points, equipment served and any locations that need to remain clear for operation or future access.

Verify busway and tap-off compatibility

Busway sections and tap-off units must be compatible with one another and with the intended installation. Confirm the specific product family, conductor arrangement, voltage, frequency, phase and neutral requirements, grounding method, enclosure type and orientation. Compatibility is not established by appearance or a similar nominal rating; equipment selection must follow the applicable manufacturer documentation.

List each proposed tap-off unit’s required configuration, including connection style and the protective device arrangement where applicable. Confirm whether the project needs a particular disconnecting means, device type or enclosure. Where equipment from multiple sources is involved, obtain exact catalog and design information for engineering review rather than assuming components can be mixed across systems.

Coordinate ratings with the distribution design

The busway rating and protective-device coordination should reflect the calculated load, demand assumptions, available supply and expected operating conditions. The responsible engineer should check conductor loading, voltage drop, fault-current conditions and coordination with upstream equipment. A suitable rating cannot be selected from connected load alone, and project conditions may affect the final design and configuration.

Confirm system voltage, phase, frequency, source characteristics, available fault current and the upstream overcurrent protection. Identify loads with starting or inrush characteristics, sensitive equipment, or operational requirements that influence circuit selection. The equipment manufacturer can use these project inputs to develop a configuration for review, but final application decisions belong to the responsible design professional and relevant authorities.

Design downstream protection intentionally

Each tap-off feeds downstream equipment, so protection must be planned as part of the overall distribution system. Identify the loads served and determine the required branch-circuit or feeder protection, disconnecting provisions and conductor routing. Check that the proposed tap-off device and downstream protective scheme coordinate with upstream protection and align with the equipment ratings and installation conditions.

Protection details depend on the project, applicable codes and selected equipment; do not treat a tap-off as a substitute for evaluating the complete circuit. Provide the engineer with load data, conductor lengths and sizes, equipment fault-current ratings, and operating priorities. Review selectivity or coordination objectives where continuity of service matters, while recognizing that achievable coordination depends on the actual devices and system study.

Keep operating and maintenance space clear

Physical access should be checked along the full busway run and at every proposed tap-off. Account for the space needed to install, inspect, operate and remove tap-off units, as well as access to associated disconnects and downstream equipment. Ceiling height, structural obstructions, lighting, piping and building services can constrain both the route and the usable connection points.

Coordinate the layout with architectural and mechanical drawings and verify clearances against applicable codes and product instructions. Consider how technicians will reach the equipment safely using the facility’s planned access method. If process changes could block a tap-off, document a keep-clear zone and assign responsibility for maintaining it in the operating layout and future modifications.

Prepare complete information for a quote

A useful quote request identifies the project location, application, desired busway route, service voltage and system details, estimated or calculated loads, and requested delivery constraints. Include plans or sketches with dimensions, elevations, supports, obstructions, proposed tap-off positions and downstream equipment. Note the number and type of connections and identify any areas where the layout remains preliminary.

Provide equipment preferences only when they are confirmed project requirements, and flag open engineering decisions rather than guessing. Include available fault-current information, upstream protection details, environmental conditions and any applicable specifications. The manufacturer can review the requested configuration and clarify information needed to build new equipment; the responsible engineer must approve the design and coordinate it with the utility and AHJ as relevant.

Coordinate fabrication, review and installation

New plug-in busway can be custom configured to suit a project’s route and connection plan. The manufacturer builds equipment in the United States with American components, offers custom fabrication and short lead times, and ships nationwide. Actual configuration, schedule and shipping arrangements depend on confirmed project information and should be reviewed during quotation and order coordination.

Before release, reconcile the approved equipment configuration with drawings, tap-off schedules, structural support details and downstream protection documents. Confirm installation requirements, interfaces and responsibilities among the manufacturer, contractor and design team. Have the responsible engineer review the electrical design, and consult the utility and authority having jurisdiction where required; verify field conditions before installation and energization.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields