Request a Quote

Serving Ohio

Newark Campus Data Room UPS Feeders

Plan dependable UPS distribution for Newark campus data rooms by coordinating feeder protection, bypass paths, load monitoring, and facility constraints. We build new custom switchboards and distribution equipment in the U.S. and ship nationwide.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Electrical equipment sections on a flatbed trailer outdoors
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Map the UPS power path

Start with a one-line diagram showing utility or generator sources, upstream distribution, UPS input, output, bypass source, and downstream panels. For a Newark campus project, identify which rooms and systems each path serves, including network racks, security, controls, cooling, and any loads intentionally left outside conditioned backup power.

Confirm the UPS topology, input and output voltages, phase, current, grounding arrangement, and available fault current at each connection. These values shape feeder and distribution equipment selection. The responsible engineer should reconcile the diagram with existing conditions, utility data, generator controls, and the facility's operating sequence before equipment is specified.

Coordinate feeder protection

UPS input, output, and bypass feeders may have different operating conditions and protection needs. Review manufacturer documentation for input characteristics, charging demand, overload behavior, and any specified upstream overcurrent protection. Confirm conductor ampacity, equipment ratings, and protection settings against the applicable design and code requirements rather than assuming one breaker arrangement fits every UPS.

Evaluate selective coordination across the complete path, from source devices to branch circuits serving critical loads. A fault downstream should be assessed for its effect on other protected loads and on UPS continuity. Request available short-circuit data, protective-device types, frame and trip requirements, and coordination-study criteria for the proposed Newark installation.

Choose a bypass arrangement deliberately

A maintenance bypass can support UPS service while transferring loads to an alternate source, but its switching sequence and interlocks require careful review. Establish which devices are operated, in what order, and whether the bypass source is compatible with the UPS output. Confirm that the design addresses inadvertent paralleling and the facility's required maintenance practices.

Distinguish maintenance bypass from static bypass and any external transfer equipment; these serve different functions and are not interchangeable. Document the desired source for bypass operation, transition expectations, isolation points, and load behavior during transfer. The UPS supplier, electrical engineer, and facility operations team should confirm a workable arrangement for the specific system.

Define monitored loads and alarms

List monitored circuits by purpose and priority, rather than treating all data room loads as equivalent. Rack distribution, network core equipment, access control, fire alarm interfaces, and cooling may have distinct backup requirements. Identify which circuits need branch-level visibility and which can be monitored at a feeder or distribution-panel level.

Specify the measurements and alarms needed by campus operators, such as current, voltage, power, breaker status, or loss of source, where supported by the selected equipment. Confirm communications protocols, points lists, network ownership, and alarm destinations. Monitoring provisions depend on the chosen devices and controls, so document required integration rather than presuming it is included.

Fit distribution to the room

Room dimensions, access routes, cable entry, working clearances, and adjacent equipment can constrain switchboard or panel placement. Capture door and corridor dimensions, floor conditions, ceiling height, and preferred front, rear, or top access. Confirm heat, ventilation, environmental conditions, and any facility restrictions that affect equipment location or maintenance access.

Review whether the project calls for a new switchboard, panelboard, or another distribution assembly, and define its interface with the UPS. UL 891 applies to switchboards; it is not a medium-voltage equipment standard. UL 1558 low-voltage switchgear is a distinct category. The responsible engineer should determine the appropriate assembly and applicable requirements.

Plan redundancy and operating states

Clarify whether the data room uses one UPS, parallel units, separate A and B distribution paths, or another architecture. Trace normal, emergency, bypass, and maintenance states to identify shared components or single points of failure. Redundancy labels alone do not establish independent paths; source connections, distribution sections, and downstream load connections matter.

For each operating state, document which loads remain energized and what actions operators must take. Consider generator transition, UPS battery operation, planned maintenance, and restoration to normal power. The design team should verify that switching procedures, protection settings, and equipment arrangement align with the campus continuity objectives and the UPS manufacturer's instructions.

Prepare project information for a quote

A useful quote request includes the one-line diagram, equipment schedules, load list, voltage and phase, required ampacity, available fault current, and specified protection devices. Add UPS make and model information when selected, bypass requirements, monitoring points, enclosure and access constraints, and the expected delivery location in Newark.

Identify project milestones, submittal expectations, field connection details, and any requirements for labeling, metering, communications, or factory documentation. Flag items still awaiting engineering decisions so assumptions are visible. We manufacture new equipment in the U.S., offer custom fabrication, and ship nationwide; project-specific scope and schedule should be confirmed with the supplier.

Verify interfaces before release

Before equipment release, compare drawings against the UPS submittal, feeder conductor plan, protection study, and room layout. Resolve differences in lug arrangements, cable entry, neutral and grounding provisions, control power, and communications interfaces. Confirm that specified devices and ratings match the approved design and the installation's available electrical data.

The responsible engineer should review the final design, while the utility and authority having jurisdiction should be consulted where their requirements apply. Coordinate installation, commissioning, and operating procedures with campus staff and the UPS supplier. Clear interfaces reduce late changes and help ensure the new distribution equipment serves the intended Newark data room loads.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields