Request a Quote

Manufacturing capabilities

Power Meter Integration

Integrate power meters into newly manufactured switchgear and distribution equipment with a plan for measurement needs, sensing inputs, mounting, communications, and field coordination.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Enclosed electrical switchboard with meters and breakers
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start With the Measurement Objective

Choose a meter based on what operators and engineers need to know: total energy, demand, voltage, current, power factor, frequency, or power quality indicators. A utility-billing requirement, internal energy report, and troubleshooting view can call for different functions. Define the use before selecting a device or specifying its display.

Identify which circuits need measurement and whether readings must be local, remotely monitored, or both. A main-incoming meter may suit facility-wide visibility, while feeder-level meters can help compare process loads. Confirm desired accuracy, reporting intervals, and data retention with the project team; do not assume every meter supports every function.

Match the Meter to the Electrical System

Provide system voltage, phase and wire configuration, frequency, grounding arrangement, and expected operating conditions when evaluating a meter. Confirm the device’s voltage-input range and whether its inputs connect directly or require instrument transformers. The responsible engineer should verify the proposed arrangement against the one-line diagram and applicable design requirements.

Meter choice also depends on panel location, environmental conditions, available control power, and the intended operating interface. Specify whether a visible display is needed at the equipment or whether readings will be accessed through a network. Confirm any required environmental ratings and mounting constraints for the actual installation rather than presuming a standard enclosure configuration.

Specify Current and Voltage Sensing

Current measurement commonly uses current transformers (CTs), but selection depends on conductor size, expected load, installation space, and the meter’s input requirements. Share the intended CT ratio, secondary rating, accuracy needs, and whether existing project standards dictate a particular arrangement. Confirm polarity, phase association, and shorting provisions with the design engineer.

Voltage sensing may use direct connections within the meter’s ratings or voltage transformers where the system design requires them. Establish nominal and maximum voltage, connection points, fusing approach, and any isolation requirements. CT and voltage-sensing circuits must be coordinated so phase readings correspond correctly; the final drawings should make these connections clear to installers.

Plan Physical Mounting and Access

Decide whether the meter belongs on a switchboard or switchgear door, an instrument compartment, or a separate panel. The choice affects viewing access, wiring routes, door cutouts, depth, and separation from power components. Provide the preferred location, device dimensions or model, and any project restrictions before fabrication drawings are prepared.

Consider how operators will read and service the device after installation. Door-mounted equipment may need clearance for opening, labels, and adjacent controls; internally mounted meters may require a safe, approved access procedure. Confirm enclosure layout, heat and environmental considerations, and whether remote displays or indicators are needed for the operating workflow.

Define Communications and Data Use

List the intended protocol, network connection, and destination system, such as a building management system, SCADA platform, or energy dashboard. Confirm whether the project expects serial communications, Ethernet, or another interface, and identify the required addressing and point list. Compatibility depends on the selected meter and receiving system, so verify it early.

Clarify who supplies network switches, gateways, configuration, and software integration. Establish whether the meter must provide alarms, demand values, interval data, or remote configuration, and document the units and scaling expected by the host system. The equipment manufacturer can coordinate meter provisions, but system-level integration responsibilities should be assigned explicitly.

Coordinate Ratings, Protection, and Standards

Meter integration must fit the equipment’s voltage class and construction. UL 891 applies to low-voltage switchboards; UL 1558 applies to low-voltage switchgear. Medium-voltage equipment follows different design and rating considerations, and UL 891 does not cover medium- or high-voltage equipment. Confirm the equipment type and project specifications before defining meter provisions.

Review sensing circuits, fusing, wiring insulation, clearances, and instrument-transformer arrangements as part of the complete design. Meter additions do not replace protection or coordination studies. The responsible engineer should verify the scheme, while the utility and authority having jurisdiction should be consulted where service rules, metering requirements, or approvals apply.

Prepare Drawings and Quote Information

For a quote, provide the one-line diagram, equipment type and voltage, service and feeder details, meter quantity, measurement points, and any specified meter models. Include CT and voltage-sensing requirements, desired display locations, communications protocol, and relevant project standards. Identify which details are fixed and which can be reviewed during engineering.

Also share enclosure constraints, installation environment, network responsibilities, delivery location, and required submittal information. A clear point list and communication boundary help distinguish equipment wiring from controls or commissioning scope. Custom fabrication is available, and short lead times and nationwide shipping can support project schedules, subject to confirmed scope and build requirements.

Review Integration Before Release

Before fabrication, review drawings for meter location, cutout dimensions, sensing connections, terminal identification, wire routing, and network interface. Check that the meter model and accessories match the approved schedule and that the point list aligns with the receiving system. Resolve open questions before release to reduce field changes and commissioning delays.

The manufacturer builds new equipment in the United States using American components and can coordinate custom meter provisions for projects in Ohio and nationwide. Final suitability depends on the approved design, selected components, and project requirements. Have the responsible engineer verify electrical details, and coordinate utility and AHJ review where applicable.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields