Request a Quote

Manufacturing capabilities

Copper Bus Fabrication

Copper buswork begins with the electrical design, then translates into controlled cuts, bends, holes, contact surfaces, and supports. Our U.S. manufacturing team fabricates new equipment for Ohio and nationwide projects.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Enclosed electrical switchboard with meters and breakers
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Buswork Starts with the Electrical Design

Copper bus is not simply a conductor cut to fit a cabinet. Its dimensions, path, joints, clearances, and supports must work together within the equipment configuration and the electrical design. Before fabrication, confirm system voltage, current requirements, fault-duty basis, enclosure arrangement, and the governing equipment standard with the responsible engineer.

The bus layout also depends on whether the assembly is a UL 891 switchboard, UL 1558 low-voltage switchgear, or another equipment type, including medium-voltage construction. Those categories are not interchangeable. Applicable design requirements, component selection, and verification depend on the specific assembly; UL 891 does not cover medium- or high-voltage equipment.

Selecting Copper Stock and Bar Geometry

Stock selection affects electrical capacity, mechanical behavior, bend feasibility, and available space. Specify the required copper grade or material standard, bar thickness and width, temper where relevant, and any project requirements for plating or finish. The design team should confirm how the intended current and temperature limits are established for the complete assembly.

Shape and orientation matter as much as nominal area. A wide, thin bar may fit one compartment but require careful support and bend planning; a thicker section can change hole-edge distances and forming limits. Provide drawings or a coordinated bus schedule that identifies phase arrangement, neutral and ground conductors, transitions, and connection interfaces.

Cutting to Length Without Losing Fit

Cutting plans establish finished lengths, end conditions, and the reference points used to locate holes and bends. Dimensions should account for joint overlap, bend geometry, enclosure boundaries, and installation access rather than measuring only the straight-line distance between connection points. Clear datums and tolerances help prevent cumulative fit errors across a bus run.

For a quote, send the latest controlled drawings, quantities, material details, and any required edge condition or deburring expectations. Identify whether bus pieces are individual replacements for a new build or part of a complete new equipment assembly. Changes to devices, compartment dimensions, or terminal locations should be resolved before release to fabrication.

Forming Bends Around Real Clearances

A bend changes the bus path, spacing, and mechanical leverage at nearby supports and joints. Confirm bend angle, inside radius, orientation, and finished dimensions against the equipment layout, while allowing for material behavior during forming. Closely spaced bends, short legs, or thick stock may constrain tooling and should be reviewed before the design is frozen.

Check phase-to-phase and phase-to-ground clearances through the entire formed route, including transitions near barriers, terminals, and enclosure walls. Required spacing depends on the equipment design and applicable requirements; it should not be assumed from a generic bus detail. Provide three-dimensional views or section dimensions when a bend passes through a tight compartment.

Drilled Holes and Connection Alignment

Hole size, pattern, edge distance, and location determine whether a joint can be assembled without forcing the bus or loading connected terminals. Drawings should define hole centers from reliable datums and state whether holes are round or slotted. Confirm fastener type, quantity, access for tools, and any joint-specific hardware requirements with the design authority.

Alignment must be checked across the mating parts, not just on each bar independently. Account for device terminal patterns, connector plates, field connections, and fabrication tolerances. Avoid relying on field enlargement or improvised slotting unless the responsible engineer approves the method and the resulting connection remains consistent with the equipment design.

Joint Surfaces, Plating, and Contact Care

Joint performance depends on compatible materials, adequate contact area, controlled surface condition, and the specified clamping arrangement. Identify whether mating faces require bare copper, tin plating, another specified finish, or a particular preparation method. Surface treatment and fastener procedures should follow the approved design rather than assumptions about a universal copper joint.

Protect contact faces from damage, contamination, and unnecessary handling during fabrication and assembly. Do not substitute abrasives, compounds, coatings, or torque values without engineering approval. If the connection joins copper to another conductor material or a device terminal, confirm the interface requirements and approved hardware for that exact connection.

Support Layout and Mechanical Restraint

Support locations influence bus deflection, vibration response, joint loading, and the available free span. Coordinate insulator type and placement, mounting points, phase spacing, and enclosure structure with the equipment design. Fault-current forces can impose significant mechanical demands, so support layout must be evaluated for the assembly's specified conditions rather than selected by appearance alone.

Review transitions, vertical runs, offsets, and connections to devices for loads that could transfer into terminals or joints. Confirm support material, attachment method, and clearances around barriers and ventilation paths where relevant. The responsible engineer should verify the layout against the design basis and applicable equipment requirements before fabrication proceeds.

What to Provide for a Fabrication Quote

A useful quote package includes the equipment type and project location, controlled bus drawings, material and finish requirements, quantities, tolerances, hole schedules, bend details, and support information. Include the relevant one-line diagram and compartment or terminal layouts when they clarify interfaces. Note the requested delivery window and identify any drawing review or approval steps.

Our U.S. team builds new switchgear and power distribution equipment with American components, offers custom fabrication, and ships nationwide, including to Ohio projects. Lead time depends on scope, design maturity, material availability, and required coordination. Confirm project-specific ratings, construction details, and compliance requirements with the responsible engineer, utility, and AHJ as applicable.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields