Request a Quote

Built for your application

Industrial Process Motor Loads

Motor-driven process equipment can impose demanding starting currents, coordinated protection needs, and control dependencies. Plan distribution around actual motor data, operating sequences, fault conditions, and the process consequences of interruption.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Enclosed electrical switchboard with meters and breakers
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

Start with the Process Duty

A motor schedule is only a starting point for distribution design. Document each motor’s horsepower or kilowatt rating, voltage, full-load current, duty cycle, driven load, and expected starts per hour. Pumps, compressors, conveyors, mixers, and fans may respond differently during startup, even at similar ratings.

Operating context matters too. Identify which motors start together, which must run continuously, and whether production depends on a specific sequence. Provide process narratives, load lists, single-line diagrams, and expansion plans so the responsible engineer can assess demand, starting impact, and equipment arrangement before a new switchboard or switchgear package is quoted.

Evaluate Starting Methods

Across-the-line starting is straightforward, but its inrush current and mechanical torque can affect voltage, driven equipment, and other loads on the system. Confirm motor locked-rotor characteristics, starting duration, load inertia, and source impedance. Utility limits or a weak plant distribution source may constrain permissible starting conditions.

Reduced-voltage starters, soft starters, and variable-frequency drives each change the electrical and operational picture. Their suitability depends on torque requirements, acceleration time, speed control, harmonics, bypass needs, and motor compatibility. Specify the intended method for every motor, and have the responsible engineer verify its effect on voltage drop, protection, and upstream equipment.

Size Feeders for Operating Conditions

Feeder planning must account for applicable electrical code requirements, motor circuit rules, conductor ampacity, ambient temperature, installation method, and the number of motors served. A shared feeder may be practical for a defined group, while critical or independently controlled loads may warrant separate circuits. Final conductor and overcurrent selections belong in the engineered design.

Running current alone does not establish whether a feeder can support startup. Evaluate voltage drop during acceleration, the impedance of transformers and upstream conductors, and simultaneous starts. Long cable runs or large starting loads can affect contactor pickup and drive performance. Provide preliminary routing lengths and source details for review rather than relying on horsepower alone.

Coordinate Short-Circuit and Overload Protection

Motor branch-circuit short-circuit and ground-fault protection serves a different purpose from motor overload protection. Select and coordinate devices for the motor, starter, feeder, and available fault current under applicable codes and equipment conditions. Confirm upstream protective-device data and the utility or facility fault-current study where available.

Adjustable trip settings, instantaneous elements, and overload-device ranges should reflect documented motor and starting information, not assumptions. Protective coordination may require a study of operating modes and fault locations. Share relay or breaker preferences, coordination criteria, and any existing settings with the design team; confirm final selections against the complete system and applicable authority requirements.

Specify Starters, Drives, and Controls

Define what each motor control position must do: local or remote operation, automatic sequencing, speed regulation, reversing, braking, or emergency shutdown. Identify control voltage, PLC or DCS interfaces, communications protocols, and required status or alarm points. These choices affect compartment layout, wiring provisions, device selection, and the interface between distribution equipment and process controls.

For variable-frequency drives, confirm input and output requirements, bypass philosophy, enclosure environment, cable considerations, and heat dissipation. Drive-generated harmonics and motor cable effects may require project-specific evaluation. Do not assume a standard control package fits every process. Submit control schematics, I/O lists, and environmental conditions for review before fabrication details are finalized.

Choose Equipment Around the System

The distribution assembly depends on voltage, system grounding, available fault current, feeder arrangement, installation conditions, and the project’s required ratings. Low-voltage switchboards built to UL 891 are distinct from low-voltage switchgear built to UL 1558; neither standard applies to medium- or high-voltage equipment. Select the equipment category with the engineer and project specification.

A motor lineup may be integrated into a new distribution assembly or coordinated with separately specified starters and drives. Confirm incoming service, bus configuration, metering, main-device requirements, cable entry, and space constraints. Custom fabrication can address project-specific layouts, but each requested feature and rating must be reviewed for the actual design rather than presumed available.

Plan for Process Continuity and Maintenance

Rank motors by their effect on production, safety systems, and recovery time. That assessment can inform feeder separation, control-power arrangements, spare-position planning, and whether selected loads need alternate sources. Any redundancy or transfer scheme requires review of the full electrical system, interlocks, operating procedure, and the consequences of parallel or sequential operation.

Also consider access for inspection, testing, cable termination, and device replacement. Confirm room clearances, working space, ventilation, ambient conditions, dust or moisture exposure, and maintenance access routes. Provide the installation location and applicable environmental requirements early; enclosure construction, internal heat sources, and equipment arrangement must suit the specific site and governing project requirements.

Prepare a Quote-Ready Motor Package

A useful request for quotation includes the motor schedule, one-line diagram, load and control descriptions, starting methods, source voltage, available fault-current information, protection criteria, and site constraints. Add specifications for metering, communications, enclosure, incoming and outgoing cable locations, and any required spare capacity. Identify unresolved items clearly so engineering review can distinguish assumptions from requirements.

A U.S. manufacturer building new equipment with American components can review these inputs, provide custom fabrication, and ship nationwide, including to Ohio projects. Lead time depends on scope, component availability, approvals, and design decisions. Before release, the responsible engineer should verify design details with the utility and authority having jurisdiction where applicable.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields