Request a Quote

Switchgear knowledge center

Motor Control Center Definition

A motor control center is a coordinated assembly of sections containing motor control units and related power distribution equipment. Its configuration depends on the loads, electrical system, operating needs, and project requirements.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Switchgear cabinets with breakers on warehouse pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

The basic definition

A motor control center, or MCC, is an assembly of adjoining vertical sections arranged to serve multiple motors and associated electrical loads. Sections house motor control units and may also contain feeder devices, buswork, control wiring, and other power distribution components specified for the application.

Rather than treating each motor starter as a separate wall-mounted installation, an MCC groups selected equipment in a coordinated structure. This can centralize motor power and control connections, but the exact arrangement varies with the facility, electrical design, operating practices, and the equipment included in the project.

What an MCC section contains

A section is a structural compartment within the overall assembly. It may accommodate one or more units, depending on their size and the manufacturer’s design. Units can be selected for motor starting, protection, isolation, or other functions identified by the project engineer and equipment schedule.

The assembly may include a common bus system, incoming provisions, outgoing feeders, and control or communication components. These are not automatic features of every MCC. Confirm which functions are required, how they connect, and whether the specification calls for particular compartments, barriers, metering, or wiring arrangements.

Motor control units and functions

Motor control units are selected around the motor and its duty. A unit might use a combination starter, variable frequency drive, soft starter, or another specified arrangement. Selection depends on motor characteristics, starting method, operating sequence, protection requirements, and compatibility with the facility’s control system.

Not every motor needs the same control method, and not every device is suitable for every application. The design team should establish motor horsepower, voltage, full-load current, starting frequency, required overload protection, and control interface. Confirm coordination and short-circuit requirements with the responsible electrical engineer.

Power distribution within the assembly

An MCC distributes power from its incoming connection through buswork and protective devices to individual motor control units or feeder circuits. The arrangement must suit the available source, system voltage, fault-current conditions, and the loads served. Incoming and outgoing connections are defined by the project design.

Bus rating, protective-device selection, conductor termination, and available fault-current withstand are interrelated decisions, not interchangeable catalog choices. The engineer should verify system studies and protection coordination as applicable. Utility requirements and the authority having jurisdiction may also affect the design, installation, and approval process.

How an MCC differs from other assemblies

An MCC is organized primarily around motor control units, although it can incorporate related feeders and distribution functions. A panelboard or switchboard may distribute power to branch circuits or larger loads without providing the same grouped motor-control arrangement. The equipment name alone does not establish its construction or ratings.

Low-voltage switchgear is a distinct equipment category from an MCC, with its own construction standards and application considerations. UL 891 applies to switchboards; it does not define medium-voltage equipment. Specify the required equipment type and applicable standard rather than assuming an MCC is switchgear or vice versa.

Configuration and installation constraints

Physical layout must account for available floor space, aisle access, cable entry, room conditions, and the planned route from the electrical source to the MCC. Section count and unit placement should reflect present loads and any documented expansion needs without assuming spare capacity that has not been designed.

Confirm enclosure requirements, environmental conditions, mounting and anchorage, access clearances, and the direction of incoming and outgoing cables. Consider heat, dust, moisture, vibration, and maintenance access where relevant. The responsible engineer and installation contractor should check the final arrangement against site conditions and applicable codes.

Information to prepare for a quote

A useful quote request identifies the supply voltage, phase and frequency, available fault current, incoming arrangement, and requested assembly ratings. Include a one-line diagram, motor schedule, load list, and control requirements when available. These documents help define sections, unit types, feeder needs, and connection details.

Also provide the project specification, applicable standards, enclosure conditions, cable-entry preferences, communication requirements, drawings, and requested delivery destination. Identify whether the project is a replacement or new installation, without assuming existing equipment can be reused. Open questions should be marked for engineering review rather than treated as settled requirements.

From design review to delivery

Before release, compare the proposed MCC configuration with the approved drawings and project requirements. Resolve discrepancies in motor data, protective devices, control interfaces, physical dimensions, and incoming connections. Any requested feature or rating should be confirmed for the specific build instead of inferred from a general product description.

A U.S. manufacturer can build new MCC and power distribution equipment with American components, custom fabrication, short lead times, and nationwide shipping. Actual configuration and schedule depend on the project scope and confirmed requirements. Have the responsible engineer, utility, and AHJ review matters within their authority.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields