Request a Quote

Switchgear knowledge center

Drawout Circuit Breaker Definition

A drawout circuit breaker is built to move within compatible switchgear between defined operating positions. Learn what those positions mean, how construction affects them, and what to confirm before specifying new equipment.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Three gray switchgear cabinets on wooden pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

What “Drawout” Means

A drawout circuit breaker is a removable breaker assembly designed to travel within a compatible switchgear or switchboard compartment. Its moving contacts engage fixed primary connections in the connected position; the breaker can also be moved away from those connections without removing the entire assembly from its compartment.

The term describes a mechanical arrangement, not a universal breaker size, rating, or interchangeability standard. Breaker, compartment, racking mechanism, interlocks, and secondary wiring are designed as a coordinated system. A drawout breaker from one assembly should not be presumed to fit or operate safely in another.

Connected, Test, and Disconnected Positions

In the connected position, the breaker’s primary contacts connect it to the equipment bus and load-side circuit. This is the normal operating position when the breaker is closed and the circuit is in service. The precise contact engagement and position indication depend on the equipment design and manufacturer’s instructions.

In a test position, primary power connections are separated while designated secondary control connections may remain engaged. This can permit selected control or operation checks, but the available functions vary by design. In the disconnected position, the breaker is withdrawn farther, with primary and, depending on construction, secondary connections disengaged.

Positions Are Design-Specific

Not every drawout design has three identically defined positions or the same means of indicating them. Equipment may use labels such as connected, test, and disconnected, with mechanical stops, position indicators, or interlocks establishing where the breaker is. Confirm terminology and functions in the equipment documentation rather than assuming a label has a universal meaning.

A breaker may be removable from its compartment after reaching a defined position, but removal procedures and access requirements are equipment-specific. Some designs include a separate withdrawn or removed state. The responsible engineer and qualified personnel should consult the manufacturer’s instructions and applicable safe-work procedures before operating, racking, or removing a breaker.

Switchgear and Switchboard Context

Drawout breakers are commonly specified in low-voltage switchgear, where service access and circuit isolation are important design considerations. UL 1558 low-voltage switchgear and UL 891 switchboards are distinct equipment categories; their construction, evaluation, and available breaker arrangements must be confirmed for the proposed assembly, not inferred from the word “drawout.”

Medium-voltage equipment has different insulation, switching, and compartment requirements. A medium-voltage breaker arrangement should be selected and described according to its applicable equipment design and standards. UL 891 applies to switchboards; it does not cover medium- or high-voltage equipment. Confirm voltage class and equipment category early in project development.

Why Project Teams Choose Drawout Construction

A drawout arrangement can support planned inspection, testing, or replacement by allowing the breaker to move out of its connected position within a designed compartment. This may help organize maintenance on multi-circuit equipment. It does not, by itself, establish that a circuit is safe to work on or substitute for required isolation and verification procedures.

The choice also affects the equipment lineup. Compartments, breaker handling, clearances, control connections, and maintenance access must be coordinated with available floor space and site practices. Evaluate the full assembly and its operating procedures, not only the breaker, when comparing drawout construction with a fixed-mounted arrangement.

Engineering Checks Before Selection

Confirm system voltage, continuous current, available fault current, protective-device requirements, and the intended source and load arrangement. The breaker’s interrupting and withstand characteristics must suit the application and the coordinated assembly. These values are project-specific; they cannot be established from the term “drawout” or from appearance alone.

Review control voltage, trip and close functions, auxiliary contacts, metering or communications needs, and any requirements for operation in the test position. Confirm enclosure conditions, bus configuration, service access, and coordination with upstream and downstream devices. The responsible engineer should check the design against project documents, utility requirements, and the authority having jurisdiction where applicable.

Interchangeability and Replacement Questions

A drawout breaker is not automatically interchangeable just because another breaker has similar dimensions or a comparable electrical rating. The compartment interface, primary disconnects, secondary plug, racking geometry, rejection features, control wiring, and tested equipment configuration can all matter. An unsuitable substitution can prevent proper engagement or defeat intended interlocks.

For replacement planning, identify the existing equipment manufacturer and model, breaker catalog or type information, nameplate data, compartment designation, and relevant drawings. For new equipment, specify the required breaker functions and positions rather than naming an unverified substitute. Have compatibility confirmed by the equipment manufacturer and responsible engineer before procurement or installation.

Information for a New Equipment Quote

A useful request for a newly manufactured switchgear or power distribution assembly includes the one-line diagram, system voltage and frequency, bus and feeder requirements, fault-current information, enclosure and installation conditions, and applicable project specifications. Identify whether drawout construction is required, which positions are needed, and what secondary functions must remain available in test.

Also provide quantity, lineup dimensions or site constraints, control schematics, metering needs, preferred equipment category, delivery destination, and project schedule. The U.S. manufacturer can review these details, discuss custom fabrication, and prepare a proposal for new equipment with nationwide shipping. Final design requirements should be checked by the responsible engineer and, where relevant, the utility and AHJ.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields