Request a Quote

Switchgear knowledge center

Current Transformer Definition

A current transformer, or CT, converts primary current into a smaller, proportional secondary signal for meters, relays or other instruments. Its ratio, accuracy, burden and installation details determine whether that signal suits the application.

01 / BUILT WITH PURPOSE SWITCHGEAR BUILDERS OHIO

Rows of gray electrical distribution cabinets on pallets
REPRESENTATIVE
EQUIPMENT
01
Made in USAAmerican manufacturing
02
UL 891 assembliesFor applicable low-voltage switchboards
03
Short lead timesTiming quoted per project

What a Current Transformer Does

A current transformer is an instrument transformer that reproduces primary-circuit current at a reduced, standardized level for measurement or protective relaying. Its primary conductor may be a separate winding or, in a window-type design, the bus or cable passing through the core. The secondary connects to instruments designed for that signal.

Unlike a power transformer, a CT is intended to represent current rather than transfer useful load power. It provides electrical separation between the primary circuit and connected devices, but it is not a substitute for protective equipment or safe work practices. The design must match the circuit, application and equipment arrangement.

How Ratio Relates to the Signal

The CT ratio expresses the relationship between primary and secondary current. For example, a 600:5 ratio ideally produces 5 amperes at the secondary when 600 amperes flow in the primary; at lower primary current, the secondary signal falls proportionally. Actual performance also depends on the CT’s accuracy limits and connected burden.

Selecting a ratio requires considering expected operating current, load growth, fault levels and the input range of meters or relays. A ratio that is too high can reduce useful resolution at normal load, while one that is too low may exceed its intended range. Confirm requirements with the responsible engineer and device documentation.

Measurement and Protection Are Different Jobs

Metering CTs support readings such as current, energy or demand, and their accuracy is specified for defined operating conditions. Protection CTs supply relays with current information during abnormal conditions. Their requirements may emphasize performance at elevated current so the relay receives a useful signal when a fault occurs.

A CT suitable for metering is not automatically suitable for protection, or vice versa. Some installations use separate cores or CTs for each function; others use a specified multifunction arrangement. Confirm relay type, metering needs, accuracy class, operating range and applicable standards rather than assuming one design covers every duty.

Burden, Accuracy and Saturation

Burden is the electrical load connected to a CT secondary, including the meter or relay input and the wiring between devices. Excessive burden can impair accuracy. Longer wire runs, smaller conductors, additional terminals and multiple connected devices can all affect the total, so the design should account for the complete secondary circuit.

During high current, a CT core may saturate and no longer reproduce the primary waveform proportionally. Saturation can affect protective-relay response and measurement. The required performance depends on fault current, system characteristics, CT class and burden. Have the engineer check these factors against relay requirements and the intended protection scheme.

Construction and Switchgear Placement

CT construction and placement depend on the switchgear design. A CT may be installed around a bus, on a cable, or as part of a specified assembly. Window dimensions, conductor size, phase spacing, insulation clearances and mounting provisions must suit the actual equipment. These details are especially important when integrating CTs into custom-built switchgear.

The selected switchgear category also matters. UL 891 switchboards, UL 1558 low-voltage switchgear and medium-voltage equipment are distinct equipment types with different design considerations; UL 891 does not cover medium- or high-voltage equipment. Confirm the system voltage, assembly type, applicable requirements and CT location for the project.

Secondary Wiring and Safe Handling

A CT secondary must be treated as a circuit that requires deliberate design and labeling. When primary current is flowing, opening an energized CT secondary can create a hazardous voltage. The installation and maintenance plan should provide appropriate shorting provisions and procedures, as required by the equipment design and applicable rules.

Secondary conductors should be identified and routed to the correct meter or relay terminals, with polarity observed where the application depends on it. Verify terminal arrangements, grounding approach, test switches and connection diagrams for the specific design. The responsible engineer and qualified personnel should review installation and service practices.

Information to Confirm Before Specification

A useful CT specification identifies system voltage, nominal and maximum load current, available fault current, ratio, intended metering or protection duty, accuracy requirements, connected device models and estimated secondary wiring burden. Include conductor or bus dimensions, phase arrangement, mounting location and any space or access constraints that affect physical fit.

Also provide the switchgear type, project drawings, one-line diagram, applicable utility requirements and requested standards or certifications. Identify whether the CT is customer-furnished or part of the new equipment supply, and clarify quantity and connection points. The manufacturer can use confirmed project information to review configuration and prepare a relevant equipment quote.

Coordinating CTs With New Equipment

For a new switchgear or power-distribution project, CT requirements should be coordinated early with metering, relaying, protection coordination and physical layout. Changes to ratio, core use, location or terminal access can affect drawings and assembly details. Build schedules around approved project information, and resolve open engineering questions before equipment fabrication proceeds.

A U.S. manufacturer building with American components can provide custom fabrication and nationwide shipping, with short lead times discussed against the actual scope and schedule. Availability and configuration depend on project requirements. The responsible engineer, utility and authority having jurisdiction should review applicable designs and interfaces before procurement and installation.

PROJECT PARAMETERS

Details make
the difference.

Every project is different. Use these points as a starting place for a conversation about your requirements.

Discuss your specifications
SPECIFICATION OVERVIEW01 — 06
Project specification overview
Equipment & scopeDefined by project requirements
Voltage classConfirm for the application
Current ratingConfirm for the application
Applicable standardsUL 891 for applicable low-voltage switchboards; other standards per specification
ManufacturingMade in USA with American components
Lead timeQuoted per project

Final configuration, ratings, standards, and timing are confirmed with your quote.

LET'S GET TO WORK

Tell us what
you’re building.

Share the essentials and start a conversation about equipment for your project.

Prefer to talk?(951) 403-5738

Email our team at saleselectricalbuyers@gmail.com.

SWITCHGEAR BUILDERS OHIO
BUILT FOR THE WORK AHEAD

PROJECT INQUIRY

Request a quote

This form opens your email application where supported. Review and send your request to saleselectricalbuyers@gmail.com from your email app; nothing is submitted directly through this website.

* Required fields